Hifonics ATLAS 6K Manuel rapide - Page 7

Parcourez en ligne ou téléchargez le pdf Manuel rapide pour {nom_de_la_catégorie} Hifonics ATLAS 6K. Hifonics ATLAS 6K 12 pages. Mt olympus

Hifonics ATLAS 6K Manuel rapide
HERCULES / ATLAS MONO AMPLIFIER APPLICATIONS

Basic application

SINGLE AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
puts with good quality RCA interconnect cables.
2. Plug the HFR-G1 remote module into the amp remote input DIN connection.
3. Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse.
4. Connect a 0 gauge ground cables directly to chassis ground with in 36" of the amp.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
5. Connect the subwoofer(s) in accordance to the diagrams below.
6. Make sure the MASTER/SLAVE switch is in the MASTER position.
Note: The amplifier will not work if the MASTER/SLAVE switch is in the Slave position
*
DESIGNATED
MONO LINE INPUT
HFR-G1
CLIP
DIAGNOSTICS
GREEN: POWER
GREEN: PRE-CLIP
AMBER: THERMAL
AMBER: SOFT CLIP
MIN
MAXX
RED: SHORT
RED: HARD CLIP
DUAL AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
puts with good quality RCA interconnect cables.
2. Plug in the HFR-G1 bass remote module into the amp remote input DIN connection
on the Master amp. This will allow the Master amp to control both Master and Slave
amps with just one Bass Remote.
3. Connect an RCA jumper cable from the Master amp MASTER OUTPUT to the
Slave amp SLAVE INPUT. Note: This will "link" the amps so that the Master amp
crossover switches will control both the Master and Slave amps. The Slave amp
crossover switches will be bypassed.
*
DESIGNATED
MONO LINE INPUT
HFR-G1
DIAGNOSTICS
GREEN: POWER
GREEN: PRE-CLIP
AMBER: THERMAL
AMBER: SOFT CLIP
MIN
MAXX
RED: SHORT
RED: HARD CLIP
Linking two amps for single or dual subwoofer application
Amplifiers are stable to 2-Ohms linked
CLIP
MODE
SLAVE IN
MASTER OUT
MODE
SLAVE IN
MASTER OUT
STEREO LINE INPUT
Note: You can use the Radio/CD designated mono line output
or a full range stereo line output. For full range stereo line
output, you will need an optional "Y-Adaptor" as shown.
SUBWOOFER
1-OHM MINIMUM
REMOTE TURN-ON
4. Route two 0 gauge power cables directly to the vehicle battery with an in-line fuse.
5. Connect two 0 gauge ground cables directly to the chassis with in 36" of the amp.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
6. Make sure the Master amp MASTER/SLAVE switch is in the MASTER position.
Make sure the Slave amp MASTER/SLAVE switch is in the SLAVE position.
7. Connect the subwoofer(s) in accordance to the diagrams below.
8. Connect a 12 gauge jumper from Master amp speaker - to Slave amp speaker - as
shown below.
MASTER OUT
SLAVE IN
MASTER OUT
SLAVE IN
FULL RANGE
Y-ADAPTOR
NOT USED
MONO
2 OHMS EACH MINIMUM
+12V
CHASSIS GROUND
TO BATTERY +12v
VIA FUSE
PARALLEL MONO
SUBWOOFERS
POWER
SPEAKER
-
-
GND
+
+
REM