Autonics MP5M-N Series Manuel du produit - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel du produit pour {nom_de_la_catégorie} Autonics MP5M-N Series. Autonics MP5M-N Series 6 pages. Thumbwheel switch multi pulse meters

Imprimer la page
Autonics MP5M-N Series Manuel du produit
■ Parameter 1 group
Parameter
Display
Default
Input
P1-1
operation
F1 F1 to F14
MODE
mode
Input A
P1-2
IN-A NPnhF NPN.H.F : NPN non-contact input1
sensor type
Input B
P1-3
sensor type
IN-B NPnhF
P1-4
Output mode OUT-T STARD
Output
P1-5
hysteresis
HYS
0001
Delay
P1-6
monitoring
GUARD fDEFY
Compensation
P1-7
time
STArT
)0
Input A
P1-8
auto-zero
AUToA 999(9
time
Input B
P1-9
auto-zero
AUToB 999(9
time
Memory
P1-10
OFF OFF, ON
retention
MEMO
01) In case of P1-1 Input operation mode F13, input B sensor type is not displayed and IN-B setting is same as IN-A.
02)  [◀] key: Entering compensation time setting.
■ Parameter 2 group
Parameter
Display
Default
Decimal
point
P2-1
DOT 00000 00000, 0000.0, 000.00, 00.000, 0.0000
position of
display value
P2-2
Time unit
01)
tUNT
tSEC
Time range
P2-3
(unit: sec)
01)
tSEC 99 (99
Time range
P2-4
(unit: min)
01)
tMIN 99 (99
Input A
P2-5
prescale
PScaH ^0000 0.0001 to 9.9999
mantissa (x)
Input A
P2-6
prescale
10 01 10 - 9 (10
PScaY
exponent (y)
Input B
P2-7
prescale
PScbH ^0000 0.0001 to 9.9999
mantissa (x)
Input B
P2-8
prescale
10 01 10 - 9 (10
PScbY
exponent (y)
P2-9
Display cycle
)05 OFF
dISpT
Input B
P2-10
setting value
COUnB 99999 1 to 99999
(INB)
01)  To enter P2-3 time range (unit: sec) and P2-4 time range (unit: min) setting, press [▲] key at P2-2 time unit.
02) Only available operation mode F2, F14
■ Parameter 3 group
Parameter
Display
Default
P3-1
Lock
LOC
OFF
Parameter
P3-2
ENA ENA: enable, DISA: disable
reset
mRST
Setting range
NPN.M.F : NPN non-contact input2
NPN.L.F : NPN contact input
PNP.H.F : PNP non-contact input1
PNP.M.F : PNP non-contact input2
PNP.L.F : PNP contact input
[Relay double output model]
STARD : S (Standard)
OUT-H : H (High)
OUT-L : L (Low)
OUT-B : B (Block)
OUT-I : I (One-shot)
OUT-F : F (Deflection) *
[Relay single / double output model]
0000 to 9999
• Varies according to P2-1 Decimal point
position of display value
[Relay double output model]
F.DEFY: L comparative output limit *
STAR.T: Start compensation timer
02)
[Relay double output model]
0.0 to 99.9 sec
0.1 to 9999.9 sec
Setting range
T.SEC, T.MIN
999.99: 999.99 s
9999.9: 9999.9 s
99999: 99999 s
999.99: 999.99 m
9999.9: 9999.9 m
99999: 99999 m
) to 10 09 (10
)
-9
9
) to 10 09 (10
)
-9
9
or 0.05, 0.5, 1, 2, 4, 8 sec
02)
Setting range
OFF : Unlock
LOC.0 : Lock All
LOC.1 : Lock parameter 1 / 2 / 3
LOC.2 : Lock parameter 2 / 3
LOC.3 : Lock parameter 3

Output Mode

Display
Output mode is available to set.
condition
The output modes supported by each model are different.
-
- Indicator : not support output mode, Relay single output model: S (Standard),
Relay double output model: total output modes
-
ON:
P1-1 Input
■ S (Standard) / B (Block) output mode
operation
mode:
• Comparative value setting condition
F2, F6 to 12,
S (Stanrdard): individual output operation regardless of size or order of set
F14
01)
comparative values
P1-1 Input
operation
B (Block): L ＜ H
mode:
H output:
Display value ≥ Comparative value H
except F11
&
L output:
Display value
* P1-1 Input
operation
mode:
H
except F14
L
P1-1 Input
operation
H
mode:
L
F1, F7 to 8
■ H (High) output mode
P1-1 Input
operation
mode:
• Comparative value setting condition:
F1 to 10
individual output operation regardless of
*P1-4 Output
size or order of set comparative values
mode: S, B, F
P1-6 Delay
H output:
Display value
monitoring:
L output:
Display value
STAR.T
P1-1 Input
H
operation
mode: F1, F4,
L
F7 to 8
H
P1-1 Input
operation
L
H
mode: F7 to 8
■ I (One-shot) output mode
P1-1 Input
operation
• Comparative value setting condition: individual output operation regardless of size or
mode:
order of set comparative values
F11 to 14
• One-shot output time: 0.3 sec (fixed)
• No hysteresis.
H output:
Display value
L output:
Display value
Display
condition
P1-1 Input
H
operation
L
mode:
F1 to 2,
H
F7 to 14
L
■ F (Deflection) output mode
P1-1 Input
• Transmits outputs when the saved setting value exceeds H deviation or L deviation.
operation
mode:
• Comparative value setting
F3 to 6
: Based on the set value, use the front HIGH / LOW set value thumbwheel switch to set
the H / L deviation.
( The set deviation value is saved during Power OFF until it is re-set.)
P1-1 Input
• Comparative value setting range
operation
mode:
: 0.0001 to 99999
F1 to 2,
The setting range is different according to the P2-1 Decimal point position of display
F4,
F7 to 14
value setting.
E.g.) In case of P2-1 Decimal point position of display value = 0000.0,
setting range = 0.1 to 9999.9
P1-1 Input
operation
• Saving setting value: [MODE] + [▲]
mode:
• Checking setting value: [▲]
F7 to 8
• The deviation can be set to "0" but the actual operation will be the same as "1".
P1-1 Input
operation
mode:
(Max.)H deviation
F1 to 2,
SV
F7 to 8, F14
(Min.) L deviation
P1-1 Input
Power
operation
mode: F14
Save SV
01)
L deviation
output
H deviation
output
01) When P1-6 Delay monitoring = F.DEFY is set, there is no output.
02) The graph is assuming that there is a saved setting value prior to the setting value save point. The actual
Display
output position may be different.
condition
-
-
OFF:
H: hysteresis
≤
Comparative value L
H
H
■ L (Low) output mode
• Comparative value setting condition:
individual output operation regardless of
size or order of set comparative values
≥
Comparative value H
H output:
≥
Comparative value L
L output:
H
L
H
H
L
≥
Comparative value H
≥
Comparative value L
0.3 s
0.3 s
Save SV
02)
≤
Display value
Comparative value H
≤
Display value
Comparative value L
H
H