DynaQuip JE3S Manuel du produit - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel du produit pour {nom_de_la_catégorie} DynaQuip JE3S. DynaQuip JE3S 2 pages. Multi-voltage on-off smart electric actuators

Imprimer la page

ELECTRICAL WIRING

Actuators are multi-voltage capable with automatic voltage sensing. Actuator

circuit should be isolated from other actuators and equipment with its own

independent, fuse protected system. All connections are made using the

supplied DIN plug connectors. The larger connectors accept 8 to 10.5 mm

diameter round cable. The smaller connectors accept 5 to 6mm diameter

round cable.

DIN PLUG CONNECTORS

Disassemble DIN connector as shown in diagram below. Wires are connected

to screw terminals marked 1, 2, 3 and ground. To access screw terminal block

(2), remove the retainer screw (4) and use a small screwdriver to pry terminal

block from housing (3). To ensure water-tightness, use correct cable diameter,

ensure connector gasket (1) is installed, and tighten retainer screw (4) securely.

Failure to do so could allow water ingress and cause major damage to the

actuator.

OPERATION: ON/OFF ACTUATORS

Standard on/off actuator requires power to open and power to close.

Actuator stays in the last known position upon loss of power. On receipt of

a continuous voltage signal, the motor runs and a flat gear system rotates

the actuator output (valve) 90 degrees. The motor is automatically stopped

in each position by internal limit switches. On receipt of a reversing

continuous signal, the motor turns in the opposite direction, reversing the

actuator position.

OPERATION: ON/OFF ACTUATOR WITH BSR OPTION

Wiring is the same as standard on/off version for actuators with BSR (Battery

Spring Return) option. The actuator requires power to open and power to

close. Actuator will move to failsafe position via battery power with loss

of external power. Actuator returns to pre-failure position upon power

resumption. Maintaining power in either the open or closed position will

trickle charge the internal battery and maintain a full charge.

JE2S - 7S Series

Power

Position

Confirmation

dynaquip.com • Tel. 800.545.3636 • [email protected]

Do not over

tighten screw

(4), correct

torque 3.5lb/in.

JE15 - 30S Series

Power

Position

Confirmation

JE Series Product Guide

Before

connecting

power, confirm

correct voltage is

being supplied.

VAC or VDC

WIRING MAIN POWER CONNECTION

Power is connected to the actuator via the large grey DIN plug connector.

Wires are connected to screw terminals located inside the connector. User/

installer to supply a three-way switch, control relay, PLC or other suitable

switching device to control the actuator position.

Power supplied to PIN 1 and PIN 2: CLOSED POSITION

Power supplied to PIN 1 and PIN 3: OPEN POSITION

Ground: Connect the flat pin on DIN connector to ground.

NOTES: The Neutral (AC voltages) or Negative (DC voltages) must be

connected to PIN 1. Power should be maintained, either in the open or

closed position to activate the internal heater. This heater will help prevent

condensation build-up inside the actuator. ACTUATOR SHOULD HAVE

ITS OWN FUSED AND ISOLATED CIRCUIT. Do not connect actuators in

parallel.

WIRING POSITION

CONFIRMATION LIMIT SWITCHES

Two auxiliary dry contact limit switches

are provided to confirm the actuator

(valve) open and closed position. Use

of these switches is optional. Switch

rating 3A@125/250VAC, 30VDC

resistive load. Do not connect a

ground to this connector.

PIN 1: Common

PIN 2: Signal to confirm

CLOSED POSITION

PIN 3: Signal to confirm

OPEN POSITION

Wire Identification for Optional Pre-Wired DIN Cables

PIN 1 - Brown

PIN 2 - Blue

Earth

Ground

Open

Closed

Customer

Supplied

Switch

Power

LS1

OPEN

Signal

PIN 3 - Black

GROUND - Green/Yellow

PN 194522.001 Rev. B

LS2

CLOSED

Signal