ADEO SCREEN FRAMEPRO PSCHT0300 Manuel de l'utilisateur - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} ADEO SCREEN FRAMEPRO PSCHT0300. ADEO SCREEN FRAMEPRO PSCHT0300 15 pages. Rigid frame screen

Imprimer la page

ENGLISH

This manual is an integral part of the product and must be read and understood in all its parts for safety reasons. It contains norms and directions for

correct and safe use of the screen. The manual should never be separated from the product; it must be stored in a suitable place to ensure its integrity,

and in such a way as to be easily consulted by authorised personnel. Product user shall be responsible for the manual's safekeeping. User shall also

be responsible for checking the screen's functionality and for the repair or replacement of any damaged parts that could pose a hazard.

Images contained in this manual are intended to provide a detailed description of the product's functions, characteristics and procedures. Any slight

difference, depending on the model represented, will not change the meaning that the images convey.

The projection screen is a cadmium-free plastic pvc sheet, with M1 and M2 fire classification under French standards (LNE Laboratoire national de métrologie et

d'essais – SME Centre de recherches du Bouchet). In the absence of a standardisation at a European level of the various national classification norms, it should be

noted that the French M1 class corresponds to non flammable material and that M2 class corresponds to flame retardant material.

Ensure that the screen has suffered no damage during transport. Promptly report any anomaly to the vendor. Verify that all screen accessories have

been included (see list below).

WARNING do not use cutters or sharp objects to open the wrapping.

REAR ELASTICS Version

a) 4 Aluminium sections for frame

b) 4 Iron angles

c) 16 Button-head screws for angles

d) 16 M6 nuts for angles

e) Projection canvas

5mm aluminium rods

g) Aluminium sliders for elastics

h) Rubber elastics for canvas anchoring

2 wall brackets (up to 3m wide)

4 spacer brackets + screws (up to 5m

wide)

8 spacer brackets + screws (up to 7m

wide)

l) Instructions

N.B versions whose horizontal or vertical sections are divided into 2 parts will include 1 joint + 4 button-head screws + 4 M6 nuts per section

Always read the instructions and warnings set out in this manual very carefully before using the product or before performing any maintenance

interventions.

- Before and during use, check that the screen poses no risk of hazard.

- Do not tamper with, remove or damage any part or component of the screen.

All our screens are covered by guarantee; validity of the same shall be subject to user's full compliance with the instructions contained in this manual.

WARNING: Faulty installation may compromise the safety of the product's operators; manufacturer shall not be held liable for damages to persons or

things resulting from faulty installation, improper use, insufficient or inadequate maintenance of the screen.

Manufacturer shall not be held responsible for problems associated with installation errors.

For any necessary clarifications please contact our technical office.

N.B.ONCE THE SCREEN HAS BEEN MOUNTED ON THE BRACKETS, AND PRIOR TO USING IT, USER IS MANDATORILY REQUIRED TO

ENSURE THAT THE SCREEN'S POSITION IS PERFECTLY HORIZONTAL.

Our screens are suitable for indoor use at normal temperature (20 - 25 ° C) and humidity conditions. Special precautions are necessary for outdoor

use, especially as regards temperature levels and the presence of dust. Exposure to temperatures of over 50 ° C can cause permanent deformation of

the screen's flatness, or the screen to come away from the roller.

Avoid prolonged exposure of the projection screen to solar light to prevent yellowing of the same (ensure that exposure to solar light does not cause

the screen to reach said temperature level).

Since electrostatic charge tends to accumulate on the projection screen (which is made of PVC), attracting dust, excessive dustiness in the projection

environment can deteriorate the optical quality of the screen (see projection screen cleaning instructions).

WARNING: Do not allow children to play with the screen's control panel. Keep remote control out of children's reach.

Monitor screen movement and allow no-one near it until it is completely closed.

Please note that the stands are designed for indoor use and for screens up to 4 m wide. For all other installations take the necessary precautions to

prevent overturning or structural collapse of the product.

Remove dust from the frame with a soft, clean cloth and a non aggressive detergent as necessary.

Clean the projection screen with a soft, clean, damp cloth, and a neutral or alcohol-base detergent as necessary. Since rubbing the screen with a cloth during cleaning

operations can cause electrostatic charge to accumulate, we recommend the subsequent application of an antistatic liquid with a clean cloth, to avoid dust being

attracted again. Periodically check the mounting system and elastics or buttons.

WARNING: When installing the screen use plugs and screws suitable for the screen's weight and for the type of wall or ceiling on which the mount

brackets are to be fixed, based on the following criteria

Screen width up to cm

Overall weight

First assemble the frame. Tighten the screws onto the angles as shown in figure 1.a and insert them into the lateral sections of the screen as indicated. In cases

where the horizontal or vertical sections are divided into two parts, insert the joint and join the profile sections together as shown in figure 1.b.

Then mount the screen according to the screen version purchased.

"Rear elastics" canvas version: insert the metal rings (provided) into the lateral eyelets and secure the canvas with the elastics as shown in figure 2.a

"Front elastics" canvas version: apply projection canvas angles with the double-sided adhesive provided, insert the metal rings into the eyelets and anchor the canvas

with the elastics as shown in figure 2.b

"Rear buttons" canvas version: secure the canvas with the buttons, starting from those placed on the corners of the frame, and subsequently using the sliders

positioned on the aluminium sections, as shown in figure 2.c.

"Front buttons" canvas version: secure the canvas with the buttons positioned on the external side of the aluminium sections, as shown in figure 2.d.

Assembly with wall mount brackets is possible for screens up to 3m wide in the "rear elastics" version: mount the brackets onto the wall, recessed by 25cm on

each side, as shown in figure 3.a; the resulting screen assembly will be flush with the wall.

Assembly with spacers applies to screens from 3.5m to 7m wide, in the "rear elastics" version, and to all dimensions of the "front elastics" version. The number

and arrangement of the spacers is shown in figure 4: mount top and bottom spacers (where required) at a distance of 6cm from the outer edge of the aluminium

section. Then loosely apply the nuts to the screws positioned on the section. Secure the screws to the spacers and tighten the nuts with a wrench following the

steps shown in figure 4.

First fix the collars to the screws of the angles or joints present on the aluminium frame, then secure the stands to the collars, as shown in figure 5.

INTRODUCTION

GENERAL CHARACTERISTICS OF THE PRODUCT

UNPACKING THE SCREEN

FRONT ELASTICS Version

a) 4 Aluminium sections for frame

b) 4 Iron angles

c) 16 Button-head screws for angles

d) 16 M6 nuts for angles

e) Projection canvas + 4 canvas angles

f) 5mm aluminium rods

g) Aluminium sliders for elastics

h) Rubber elastics for canvas anchoring

i) 2 spacer brackets + screws (up to 3m wide)

4 spacer brackets + screws (up to 5m wide)

8 spacer brackets + screws (up to 7m wide)

l) Instructions

GENERAL SAFETY NORMS

WARNINGS AND RECOMMENDATIONS FOR CORRECT USE

CLEANING AND MAINTENANCE

INSTALLATION INSTRUCTIONS

160

Kg 11

STANDS INTALLATIONS

REAR BUTTONS Version

a) 4 Aluminium sections for frame

b) 4 Iron angles

c) 16

Button-head

screws

angles

d) 16 M6 nuts for angles

e) Projection canvas

f) Aluminium sliders for buttons

g) 2 wall brackets (up to 3m wide)

4 spacer brackets + screws (up to

5m wide)

8 spacer brackets + screws (up to

7m wide)

l) Instructions

200

250

300

360

Kg 13

Kg 17

Kg 22

Kg 27

FRONT BUTTONS Version

a) 4

Aluminium

sections

frame

for

b) 4 Iron angles

c) 16 Button-head screws for

angles

d) 16 M6 nuts for angles

e) Projection canvas

f) 2 wall brackets (up to 3m

wide)

4 spacer brackets + screws (up

to 5m wide)

8 spacer brackets + screws (up

to 7m wide)

l) Instructions

400

500

600

700

Kg 32

Kg 43

Kg 53

Kg 63

for