ADEO SCREEN PROFESSIONAL PSCHP0099 Manuel de l'utilisateur - Page 5

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} ADEO SCREEN PROFESSIONAL PSCHP0099. ADEO SCREEN PROFESSIONAL PSCHP0099 14 pages.

TROUBLESHOOTING OF THE MOTORISED SYSTEM:
1)
Check the power supply 230 V on the control commutator.
2)
Check the connections between the control commutator and the motor.
3)
Check that the motor is not in the phase of thermal protection (wait few minutes to cool the motor).
4)
Check that the wire between the motor and the inverter is not cut.
FEATURES:
T he motor is realised with a tubular asynchronous monophasic runner with the following features:230V, 50 Hz, 90 W, 17 revolutions per minute.
T he motor of the screens with case is located in the right side of the screen (on request it is possible to have it on the left) if the screen is without case the motor is located on the left.
It works through a radio remote control supplied from the producer.
ELECTRIC CONNECTIONS:
T he electric cabling must respect the CEE regulations. According to the CEI 335-1 norm, you have to install an upstream omni polar switchgear with a minimum contacts opening
spacing of 3 mm. Please follow the instruction on the connection scheme see FIG 5.
MEMORISING THE "FIRST" TRANSMITTER ON SCREEN
Caution! – DO NOT follow this procedure if Transmitters hav e already been memorised on screen
01. T urn on the power to screen: the motor makes 2 LONG motions (= no transmitters memorised).
02. (Within the next 5 seconds) Press and hold down key
memorisation complete).
Caution! – Once this part of programming has been completed, the Up and Down mov ements of the motor are still not associated to keys
This will take place automatically during one of the three programmino procedures of limit switches "0" and "1".
PROGRAMMING OF LIMIT SWITCH POSITIONS upper "0" and lower "1"
01. Press and hold down key
(or
AT T ENT ION! ! ! the correct "0" position is when the low bar of the screen is positioned at 2 mm from the case.
02. Press and hold down key
until the motor performs 1 VIBRAT ION; then release the key.
03. Press and hold down key
again (for approx. 5 seconds), until the motor performs 4 SHORT motions; then release the key.
04. Press and hold down key
until the motor performs 2 LONG motions (= the "0" position is memorised); then release the key.
05. Press and hold down key
(or
06. Press and hold down key
until the motor performs 1 VIBRAT ION; then release the key.
07. Press and hold down key
again (for approx. 5 seconds), until the motor performs 4 SHORT motions; then release the key.
08. Press and hold down key
until the motor performs 2 LONG motions (=position "1" is memorised); then release the key.
Note – Once this programming procedure is complete, key
manoeuvre. T he roller shutter/awning will stop at programmed positions "0" and "1" during each of these manoeuvres.
REPOSITIONING OF LIMIT SWITCH lower "1"
01. Press and hold down key
(for approx. 5 seconds), until the motor performs 1 VIBRAT ION, then release the key.
02. Press and hold down keys
and
the keys.
03. (within the next 4 seconds) Press keys
04. (within the next 4 seconds) Press and hold down keys
DELETING TRANSMITTERS FROM THE MEMORY
Caution! – This procedure deletes all memorised transmitter codes from screen memory. The procedure can be performed both with a memorised transmitter as well as
a non memorised transmitter.
If the transmitter is memorised, proceed as follows:
01. Press and hold down key
(for approx. 5 seconds), until the motor performs 1 VIBRAT ION; then release the key.
02. Press and hold down key
until the motor performs 3 LONG motions; then release the key exactly on the third movement.
03. Press and hold down key
until the motor performs 3 LONG motions; then release the key exactly on the third movement.
04. Press and hold down key
until the motor performs 3 LONG motions; then release the key exactly on the third movement.
After a few seconds the motor performs 5 LONG motions (= all transmitters deleted).
If the T ransmitter is not memorised, proceed as follows:
A. Disconnect from power supply (if connected) and connect again the tubular motor to the power supply. Within the next 60 seconds,
press and hold down key
(for approx. 5 seconds), until the motor performs 1 VIBRAT ION; then release the key.
B. (within the next 5 seconds) Disconnect from the power supply.
C. Power the motor again: the previous procedure, from point 01 to point 04, must be performed within 60 seconds from turning on the
power supply.
TROUBLESHOOTING OF THE MOTORISED SYSTEM:
1)
Check the power supply 230 V.
2)
Check that the motor is not in the phase of thermal protection (wait few minutes to cool the motor).
3)
Check that the wire between the motor and the power supply is not cut.
ATTENTION the installation of the screen, the electric connections, the setting of the limit switches and the test of malfunctions of the motorised rolling up and
down, must be made from authorised staff only. It is not possible to change the connection cable. If the cable is damaged the screen must be changed.
The warranty is not v alid in case of wrong installation, tampering or repair by technicians not authorized or tampering of the seal of limit switches.
If necessary, for further information ov er these points contact our technical office.
Adeo Screen screens are covered by 24 months Manufacturer' s Warranty on the curtain + 12 months on mechanical and structural parts only ( electric engines covered by
independent 60 months warranty ). T he warranty starts from the date of the manufacturer' s invoice. Adeo Screen warranty covers damages and malfunction deriving from normal use
of the screen and free of charge replacement of defective parts.
Withdrawal of screen, forwarding charges and custom duties are to be paid by the customer.
T he warranty is not valid in case of wrong installation, tampering or repair by technicians not authorized by Adeo Screen or tampering of the seal of limit switches. The adjustment of
limit switches must be done only by technicians authorized by Adeo Screen. T he warranty does not cover the parts that show normal wear and tear, deriving from particular weather
or environmental conditions as well.
Damages or tampering of screens in transit/shipment are not covered by warranty: an accurate inspection when goods are collected/received is, therefore, recommended. T he
screens sent back to be repaired will not be accepted without a Return Material Authorization number (R.M.A.) FROM Adeo Screen and/or without a proper packing.
Adeo Screen reserves the right to check that all the details above mentioned have been complied with in order to consider the warranty valid.
RADIO INTEGRATED MOTORIZED SCREENS (Fig.5)
on the transmitter for about 3 seconds and release it as soon as the motor start the first of 3 LONG motions (=
) on the transmitter until the roller shutter/awning reaches the "0" position required by the user; then release the key.
) until the roller shutter/awning reaches the position "1" required by the user; then release the key.
on the T ransmitter will control the Up manoeuvre of the roller shutter/awning, while key
simultaneously (for approx. 5 seconds), until the motor starts to automatically move the roller shutter / awning into position "1", then release
and
to position the roller shutter/awning in the new position "1".
and
simultaneously until the motor performs 2 LONG motions (= new position "1" memorised), then release the k ey s.
WARRANTY ON SCREENS
and
on the Transmitter.
will control the Down