Autopot AUTO5XL9 Manuels d'entretien simples - Page 2
Parcourez en ligne ou téléchargez le pdf Manuels d'entretien simples pour {nom_de_la_catégorie} Autopot AUTO5XL9. Autopot AUTO5XL9 2 pages.
Imprimer la page
Auto5 Kit - contents
• 1x Auto5 lid
• 1x AQUAvalve PotSock
• 1x 4ft x 4ft garden tray
• 1x metal plate for PotSock
• 1x round blue access cover
• 1x metre 3/8" piping
• 5x 9 gal fabric SpringPot
• 1x 3/8" top hat grommet
• 1x AQUAvalve5
• 1x drill template
• 1x AQUAvalve Cover
Required Reservoir Capacity
FlexiTank and FlexiTank Pro are the only collapsible reservoirs
that AutoPot recommend for use with Auto5 Systems.
A minimum 25 gallon reservoir is required per unit.
FlexiTank or
Auto5
FlexiTank Pro Capacity
System Size
FlexiTank / Pro 25 gal
1x Auto5
FlexiTank / Pro 60 gal
2x Auto5
FlexiTank / Pro 105 gal
4x Auto5
FlexiTank 200 gal
8x Auto5
FlexiTank 265 gal
10x Auto5
•
Please note that multiple FlexiPots may increase room humidity due to the exposed surfaces of the fabric pots.
•
Pot up your plants, water through, then allow your plants to establish in the pots for a period of 10 to 14 days before
turning your system on. This will encourage a stronger and healthier root system.
•
Always raise your reservoir to a minimum of 6" above the highest AQUAvalve and re-fill the reservoir when there is
approximately a 1/3 of the solution left - NEVER ALLOW THE RESERVOIR TO RUN EMPTY.
• With AQUAvalve5 systems mineral or organic fertilisers may be fed via the reservoir and pipework. Organic
fertilisers will require a water pump in the reservoir running for 15 mins every 2 hrs and cleaning of the reservoir,
pump, and filter each time the reservoir empties. Flush pipework with plain water every time the reservoir empties.
•
Clean all substrate from the bottom and sides of the pots before placing in trays to ensure AQUAvalve functionality.
•
Always use free draining substrates, for example: soil/perlite, coco/perlite, soil/clay pebbles, coco/clay pebbles,
rockwool/clay pebbles.
[email protected] I www.autopot-usa.com I +(1) 702 338 0373
Auto5 No Pots - contents
• 1x Auto5 lid
• 1x AQUAvalve PotSock
• 1x 4ft x 4ft garden tray
• 1x metal plate for PotSock
• 1x round blue access cover
• 1x metre 3/8" piping
• 1x AQUAvalve5
• 1x 3/8" top hat grommet
• 1x AQUAvalve Cover
• 1x drill template
Auto5 Basic - contents
• 1x Auto5 lid
• 1x round blue access cover
• 1x 4ft x 4ft garden tray
• 1x drill template
Pot and Tray Dimensions
15"
SpringPot
9 gal
48"
Advice
Auto5 Setup
1
3
5
7
4.1"
9
11
Allow your plants to establish for 10-14 days before turning system on
Advice
2
Mark here
Fill pots with medium
24"
and pot up plants.
Water through pots
and allow to drain
outside the tray.
4
At the marked halfway
point stand the drill
template upright against
the inside of the tray wall.
Mark drilling position in
centre circle of template.
6
From the outside of the
tray push 3/8" top hat
grommet into the 1/2" hole
in the Auto5 tray wall.
Thread 3/8" pipe into the
tray through the grommet.
8
Attach the AQUAvalve to the
3/8" pipe inside the tray.
Remove AQUAvalve collar.
Push pipe through collar and
attach to AQUAvalve nozzle.
Rescrew collar - DON'T
overturn... when you
feel it grip STOP.
10
Taking the end of the 3/8"
pipe outside the tray, cut
to an appropriate length.
Connect via 3/8" / 1/2"
fittings to a filter (not incl.).
Connect filter to reservoir.
Leave tap off.
12
Brush down the pots to
ensure they are clean
and free of debris.
If you require any guidance email - [email protected]
The garden tray requires
drilling for pipe access.
Measure to the halfway
point along any one of
the tray sides (24").
Mark halfway point on the
inside of the tray side.
At the drilling position
use a STEP DRILL BIT
to drill from the inside
of the tray outwards.
Drill a 1/2" diameter
hole in the wall.
Place AQUAvalve PotSock
in the tray, copper side
facing out, shortest side
facing the tray wall, in
line with the 3/8" pipe.
Place metal plate
in the PotSock.
Place the connected
AQUAvalve on the metal
plate in the tray.
Place the AQUAvalve cover
over the AQUAvalve.
Remove any slack from 3/8"
pipe by drawing excess
pipe out of the tray.
Ensure that the circular spirit
level indicates the tray is
level, adjust if required.
Make sure the system is
clean and free of debris.
Place the lid on top of the
tray. Insert the pots. Place
the round blue access
cover over the valve.