AutoSat GPS-GPRS Video Manuel d'instruction - Page 8
Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} AutoSat GPS-GPRS Video. AutoSat GPS-GPRS Video 8 pages. Satellite car alarm
Imprimer la pageENGLISH
To request the last GPS position (command "!POSI")
To request the last position of the vehicle, send an SMS command message to the AutoSat
SIM card using the format shown below:
!POSI#PSW#
The AutoSat will reply: Info GPS: speed' 18 km/h;latitude 41,7109 north;
longitude 12,6284 east.
NOTE
The data is in decimal therefore map software must be compatible.
To request the status of the installation (command "!STAT")
It is possible to monitor the AutoSat installation by means of SMS request command
messages. Example: by sending SMS message to the AutoSat SIM as shown below:
!STAT#PSW#
Example: !STAT#1234#
AutoSat replies: Mode: Active. Received field: G**. Cameras: 2.
Photos in memory: 0.Photo memory: 0%. FIX GPS: ON. MemLGPS: ON
Battery back-up: recharging (65%).
Meaning of the information received:
● Mode: Active or stand-by.
● Received field: G**. The "G" indicates presence of GPRS network, while the power
level of field is represented by the number of asterisks (*), from 1 to 4.
● Cameras: Indicates the number of cameras installed, from 0 to 3.
● Photos in memory: Indicate the number of images in memory.
● Photo memory: Indicates the percentage (%) of memory occupied (max 512 KB).
● FIX GPS: Indicates if the GPS receiver is obtaining satellite information (ON - OFF).
● MemLGPS: If "ON" indicates that the tracking memory is in function, if "OFF", the
tracking memory is not in function.
● Battery back-up: Indicates the condition of the back-up battery with percent charging
level(%). Possible states:
- Charging
- Stand-by or fully charged
- Operative (this state only if there is no power to the AutoSat)
Request to cancel memorized images (command "!DELI")
It is possible to cancel the AutoSat image memory by sending an SMS message to the SIM
card inserted in the unit with the following format:
!DELI#PSW#
Example: !DELI#1234#
AutoSat replies: Image memory cancelled.
NOTE
After having sent this command, the images in memory will be deleted and the
AutoSat is ready to store new images.
Page 8
AutoSat GPS - GPRS video instruction manual
To cancel the GPS data in memory and memorize new data (command "!DELG")
To cancel the GPS data memorized, send an SMS command to the AutoSat using the
following format:
!DELG#PSW#option
-
If option = 'S', the GPS memory will be cancelled and new data will be stored (see
command "!LGPS" in paragraph 3.3 on Page 10).
-
If option is omitted, new GPS data will not be memorized.
Example: !DELG#1234#S
AutoSat replies: GPS memory cancelled. Memory LGPS started.
NOTE
The AutoSat will memorize the GPS co-ordinates only after the above command
is sent with the "S" option.
The unit must be in active mode in order to accept this command.
To check memorized telephone numbers and e-mail addresses (command "!MEMO")
To check the e-mail addresses and telephone numbers memorized in the AutoSat, send an
SMS command message to the SIM card inserted in the unit using the following format:
!MEMO#PSW#
AutoSat replies: MEMO: A#[email protected];[email protected];
[email protected] /3288941292,B;3294708725,R
In this case, as specified in paragraph 3.1, the option = 'A' indicates that the e-mails are
sent automatically in case of alarm trigger.
For the two memorized telephone numbers, option 'B' indicates that the 1
of alarm trigger, there will be a ring and alarm SMS.
To the second number (option 'R') the transmission of alarm will be sent with only a ring of
the telephone, no SMS message will follow.
Control of the memorized parameters related to the SIM card (command "!
RPAR")
To request the memorized parameters of the AutoSat SIM card, send an SMS message to
the SIM card of the AutoSat with the format shown below:
!RPAR#PSW#
Example: !RPAR#1234#
AutoSat replies: RPAR: [email protected], brown, test
Control of the APN and SMTP memorized parameters related to the SIM card (command "!
RAPS")
To request the memorized APN and SMTP parameters of the AutoSat SIM card, send an
SMS message to the SIM card of the AutoSat with the format shown below:
!RAPS#PSW#
AutoSat GPS - GPRS video instruction manual
ENGLISH
st
number, in case
Page 9