Agrotechnic X.Quattro Manuel d'utilisation - Page 6

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Agrotechnic X.Quattro. Agrotechnic X.Quattro 7 pages. Olive harvester

Imprimer la page

Operation

Area of use

The X.Quattro Superveloce Olive Harvesting

Machine is suitable for all varieties of olive trees.

Preparation

Place the olive collecting nets covering the area under

the olive tree. Place the 12VDC car battery near the

operating area.

Starting Operation

Before connecting the olive harvesting machine to

the power source, make sure that the on-off switch

is in the OFF (O) position and the speed control knob

(Fig.1 - E) is turn fully anti-clockwise.

Align the slot at the bottom of the tube with the slot

of the brace (Fig.2 - Step1).

Insert the motor's coupling unit inside the coupler in

the tube. Until there is no gap between the tube and

the motor. (Fig.2 - Step2).

Lower the tube clamp and tighten the butterfly screw

firmly (Fig.2 - Step3).

Connect the alligator clips of the power cable to the

12VDC car battery.

Black cord connects to the negative terminal (-).

Red cord connects to the positive terminal (+).

To start the operation hold the olive harvesting

machine with both hands and push the on-off switch

to the ON (l) position.

You can adjust the speed of the machine, by turning

the speed control knob (Fig.1 - E) clockwise. Set at

the desired speed.

Olive harvesting techniques

After starting the operation, lead the head of the

olive harvesting machine to the branches of the olive

tree, where the olive seeds are.

The head vibrates and the olive seeds drop onto the

nets. Repeat until all olive seeds of the tree have

been dropped on the nets.

Maintenance

General

Before doing any cleaning or maintenance, make

sure that the power source is disconnected.

Always use original replacement parts. Never use

replacement parts that might be same visually, but

without the required specifications.

Storage and transportation

The olive harvesting machine should be thoroughly

cleaned and stored in good condition.

Store/transport the olive harvesting machine in a dry

and safe place away from humidity and sun rays.

Apply spray grease externally to the ball bearings of

the head

(Fig.8

) before storage.

Some parts of the olive harvesting machine are

subject to normal wear even when used properly

and must be replaced in due time depending on

type and duration of use. These parts are not covered

by the warranty.

These parts are:

- Elastic semispheres and carbon sticks

- Power cable

- Fuse

- Electronic module

The following parts can be easily replaced by the user.

For any further maintenance and repair work please

contact your supplier.

Before doing any maintenance, move the On-Off switch

to the OFF (O) position. and disconnect from the power

source.

Cleaning your olive harvesting machine

Clean parts using a damp cloth and dry them

thoroughly. Do not use any aggressive cleaning

agents - this may damage some plastics.

Replacing the elastic semispheres

To replace the elastic semispheres, using a No.11

wrench, unscrew the nuts at the ends of the shafts on

the head (Fig.3 + Fig.4). Replace the elastic

semispheres and tighten the nut.

Tip: To unscrew more easily you can hold the resistance

on the other semisphere with your hand or the other

side's self locking nut with a pliers or 11mm wrench.

Replacing the carbon sticks

To replace the elastic sticks, hold the semisphere firmly

on a workbench. With a pliers pull out the worn out or

broken carbon stick (Fig.5). Insert a new one in the

same cavity by pushing the spherical end side into the

cavity until it snap-locks in place (Fig.6).

Replacing the power cord

Power cord must be in excellent condition at all

times. You can visually examine it for any defects.

To replace the power cord, unscrew the 2 torx screws

using a T20 bit at the back side of the motor

Slide back the terminals of the power cord and discard

it. Insert the new power cord to the cable cover

with strain relief and attach the cable's terminals on

the rocker switch terminals. Tighten the 2 screws firmly.

Replacing the fuse

In case of a short circuit, the electrical system is

protected by a melting fuse, located inside the fuse

holder near the end of the power cord.

After locating and repairing the short circuit, open

the fuse holder

(Fig.1 - I)

with a new 30A melting fuse.

Lubrication

Lubricate the X.Quattro mechanism

externally (Fig. 8)

every 10 hours of operation using

grease spray.

Lubricate the internal guide rollers every of

operation using NGLI-2

(Fig.7).

and pull out the fuse, replace

and ball bearings

grease.

p. 5