Gallien-Krueger 1001RB/210 Manuel du propriétaire - Page 6

Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} Gallien-Krueger 1001RB/210. Gallien-Krueger 1001RB/210 16 pages. Artist series
Également pour Gallien-Krueger 1001RB/210 : Manuel du propriétaire (17 pages)

Imprimer la page
Gallien-Krueger 1001RB/210 Manuel du propriétaire

Quick Start

The 1001RB-II/700RB-II is designed to be simple to
operate. All controls have a well defined purpose and
are well behaved. These directions will take you
through the basics and give you a good start for
setting up your sound.
1. Plug it in:
Set the power switch to Off and connect the supplied
power cord, from the amplifier AC receptacle, to an AC
power outlet of proper voltage and power rating (see
safety information on page 5 for details).
2. Connect your cabinets:
Connect your speaker cabinets to the amplifier
outputs marked 700W/480W AMP ONLY or
"SPEAKON" OUTPUTS. Be sure not to exceed the
recommended speaker load below.
Maximum Recommended Speaker Loads:
One 4 Ohm, or two 8 Ohm cabinets on the Woofer
Amp. One or two 8 Ohm horns on the 50W/Tweeter
Amp.
If you are using an RBH Series cabinet, use the
supplied 4 conductor Speakon cable to connect to the
"Speakon" outputs on the rear panel of the amplifier.
In addition, set the switch on the RBH cabinet to "Bi-
Amp".
For connection to all other cabinets, connect to the
1/4" outputs labeled 700W/480W amp only.
For more information on Bi-Amp and Normal mode,
see page 7.
Caution:
Do not connect any Speakon cables labeled "Bridge
Mode" to the 1001RB-II/700RB-II. These cables are
used for the old 2000RB amplifier only, and may
result in damage to your amplifier.
W h e n u s i n g n o n - G K c a b i n e t s t h a t h a v e
W h e n u s i n g n o n - G K c a b i n e t s t h a t h a v e
W h e n u s i n g n o n - G K c a b i n e t s t h a t h a v e
W h e n u s i n g n o n - G K c a b i n e t s t h a t h a v e
W h e n u s i n g n o n - G K c a b i n e t s t h a t h a v e
S p e a k o n c o n n e c t o r s , o n l y u s e a s t a n d a r d t w o
S p e a k o n c o n n e c t o r s , o n l y u s e a s t a n d a r d t w o
S p e a k o n c o n n e c t o r s , o n l y u s e a s t a n d a r d t w o
S p e a k o n c o n n e c t o r s , o n l y u s e a s t a n d a r d t w o
S p e a k o n c o n n e c t o r s , o n l y u s e a s t a n d a r d t w o
wire Speakon cable. The supplied four
wire Speakon cable. The supplied four
wire Speakon cable. The supplied four
wire Speakon cable. The supplied four
wire Speakon cable. The supplied four
c o n d u c t o r S p e a k o n s t y l e c o n n e c t o r c o u l d
c o n d u c t o r S p e a k o n s t y l e c o n n e c t o r c o u l d
c o n d u c t o r S p e a k o n s t y l e c o n n e c t o r c o u l d
c o n d u c t o r S p e a k o n s t y l e c o n n e c t o r c o u l d
c o n d u c t o r S p e a k o n s t y l e c o n n e c t o r c o u l d
r e s u l t i n d a m a g e t o y o u r a m p l i f i e r
r e s u l t i n d a m a g e t o y o u r a m p l i f i e r. . . . .
r e s u l t i n d a m a g e t o y o u r a m p l i f i e r
r e s u l t i n d a m a g e t o y o u r a m p l i f i e r
r e s u l t i n d a m a g e t o y o u r a m p l i f i e r
700RB-II/1001RB-II Series
3. Initial front panel control settings:
Set all EQ controls and the Boost control to 12
o'clock.
way down to get a flat response. Set the Level and
Master Volumes at 0. If you have a five string bass,
push the button marked String Bass in.
4. Plug in your bass:
Using an instrument cable, connect your bass to the
Input jack and press the power switch on. If you have
active tone controls on your bass, turn all of the
controls to the middle or flat position and turn the
volume all the way up. If you have conventional,
passive tone controls, turn all tone and volume
controls all the way up.
5. Level and Master Volume settings:
Set the Master Volume to 12 o'clock. Turn the Input
volume up as you play. Try not to turn it past 1
o'clock unless you want an overdrive effect. If the
yellow clip light turns on, press the -14db button in.
If it is still on, try turning the volume down on your
bass.
At this point:
You should be hearing your bass quite well. You can
use the Volume and Woofer-Master to achieve a
comfortable sound level. R e m e m b e r :
more volume, turn up the Woofer-Master control first.
6
The Voicing Filters should be turned all the
R e m e m b e r :
R e m e m b e r :
R e m e m b e r : If you need
R e m e m b e r :