Dea TEO 700 Mode d'emploi et avertissements - Page 4
Parcourez en ligne ou téléchargez le pdf Mode d'emploi et avertissements pour {nom_de_la_catégorie} Dea TEO 700. Dea TEO 700 16 pages. Sectional door electromechanical operator
Également pour Dea TEO 700 : Mode d'emploi et avertissements (20 pages)
Imprimer la page
2 PRODUCT DESCRIPTION
Models and contents of the package
Under the name TEO 700 is identified a family of 24V electromechanical operators with built-in control board for adjusting the forces
while opening/closing and for managing optional features such as photocells, automatic closing, etc. .. Functions OPEN - CLOSE - STOP
operated by a single key, change of direction when an obstacle is detected in closing, led courtesy light in opening and closing with auto-
off after 3 minutes, protective functions for inputs in low and high voltage, short circuit, etc. .
TEO 700 is an electromechanical operator for the automation of sectional, overhead counterweight and spring doors. It is basically
made up of a mechanical operator rotating the draft gear that, through a chain, transmits the movement directly to the door draft system
thus moving it.
Inspect the "Content of the package" (Pic. 1) and compare it with your product for useful consultation during assembly.
Transport
TEO 700 is always delivered packed in boxes that provide adequate protection to the product, however, pay attention to all informa-
tion that may be provided on the same box for storage and handling.
3 TECHNICAL DATA
Power supply (V)
Rated power transformer (VA)
Fuse F2 (A) (transformer)
Auxiliaries power supply output
Flashing light output
Receiver frequency
Transmitters type of coding
Max remote controllers managed
4 INSTALLATION AND ASSEMBLY
4.1 For a satisfactory installation of the product is important to:
• Ensure the door frame is solid and suitable to be driven;
• Make sure that during its movement it doesn't present friction points;
• Check it is well balanced. If required adjust the balancing mechanisms;
• Foresee an adequately protected 230V socket near the automation.
4.2 Defined and satisfied these prerequisites, proceed to the assembly:
• Assemble the track (2) to the main unit (1) by inserting the motor pin inside the pinion (Picture 3);
• Fix the track to the main unit by using the two supports (3);
• Mount the angular support bracket (4) and fix it with the fixing support (we suggest to keep it as close as possible to the main unit);
Warning: bigger is the distance of the angular support from the main unit, smaller is the part of track available.
• Combine the angular support with the two ceiling fixing brackets (5) (adjust the brackets so that the track, once fixed, is perfectly horizontal);
• Fix the front bracket (6) to the track fork;
• Mount the release blade (8) on the release base (7) positioned on the track and fix it with the 4 screws provided (Picture 4);
• Secure the track to the door frame (if possible) or to the wall with screws or bolts suitable to the material respecting a distance of at least
40mm. from the maximum door stroke;
• Lift the main unit and fix it to the ceiling by using proper tools for the material/surface (Picture 5);
• Combine the straight lever (9) with the curved one (10) and fix them to the release blade;
• Combine the connecting bracket (11) to the curved lever and then secure them on the top side of the door to be moved by using proper
tools for the material/surface;
Warning: Once the connecting bracket is mounted on the door, the curved lever must be horizontally positioned;
• If the chain get loose, tighten the nut on the front side and adjust tension without overdoing (Picture 6);
4.3 How to unlock the operator
All TEO 700 models are equipped with a release device that is activated by pulling down on the handle shown in Pic. 7, now if no
obstructions hinder its movement, the door can now move freely. The door will be locked again automatically with the first travel thus
returning the operator to its normal working conditions.
10
CONTROL BOARD
230 V ~ ±10% (50/60 Hz)
100 VA (230/22V)
2,5A 250V
+24 V
max 200mA
24 V
max 15W
433,92 MHz
HCS rolling code
20
TEO 700
Motor power supply voltage (V)
Absorbed power (W)
Max Thrust (N)
Work cycle (cycles/hour)
Maximum n° of operations in 24 hour
Operating temperature range (°C)
Opening speed (m/min)
Weight of product with package (Kg)
Protection degree
OPERATOR
24 V
100
1000
15
35
-20÷50
9
4,3
IP30