HIKOKI DV 18DGAL Manuel d'instructions de manutention - Page 6
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions de manutention pour {nom_de_la_catégorie} HIKOKI DV 18DGAL. HIKOKI DV 18DGAL 16 pages.
Imprimer la pageNOTE
The recharging time may vary according to the ambient
temperature and power source voltage.
CAUTION
When the battery charger has been continuously used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next charging.
4. Disconnect the charger's power cord from the
receptacle.
5. Hold the charger fi rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
CAUTION
○ If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used, the
pilot lamp of the charger lights for 1 second, does not
light for 0.5 seconds (off for 0.5 seconds). In such a case,
fi rst let the battery cool, then start charging.
○ When the pilot lamp fl ickers (at 0.2-second intervals),
check for and take out any foreign objects in the charger's
battery connector. If there are no foreign objects, it is
probable that the battery or charger is malfunctioning.
Take it to your authorized Service Center.
○ Since the built-in micro computer takes about 3 seconds to
confi rm that the battery being charged with charger is taken
out, wait for a minimum of 3 seconds before reinserting
it to continue charging. If the battery is reinserted within
3 seconds, the battery may not be properly charged.
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
Tightening torque adjustment
Selecting the drill position
Selecting the impact position
Change rotation speed
How to use the LED light
Mounting the bit
Reversing the rotational direction
Switch operation
Using the bit holder
Selecting accessories
MAINTENANCE AND INSPECTION
1. Inspecting the tool
Since use of as dull tool will degrade effi ciency and
cause possible motor malfunction, sharpen or replace
the tool as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Cleaning on the outside
5. Storage
NOTE
CAUTION
Important notice on the batteries for the HiKOKI
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
batteries other than these designated by us, or when
Figure
Page
the battery is disassembled and modifi ed (such as
disassembly and replacement of cells or other internal
1
10
parts).
2
10
3
10
GUARANTEE
4
10
We guarantee HiKOKI Power Tools in accordance with
5
10
statutory/country specifi c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
6
10
normal wear and tear. In case of complaint, please send
7
11
the Power Tool, undismantled, with the GUARANTEE
8
11
CERTIFICATE found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
9
11
10
11
11
11
Information concerning airborne noise and vibration
The measured values were determined according to
―
12
EN60745 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 93 dB (A)
Measured A-weighted sound pressure level: 82 dB (A)
Uncertainty K: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined
according to EN60745.
Impact drilling into concrete:
Vibration emission value
Uncertainty K = 1.5 m/s
6
When the driver drill is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
Store the power tool in a place in which the temperature
is less than 40°C and out of reach of children.
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signifi cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However, signifi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to fi ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
a
h , ID = 12.1 m/s
2
2