Bristan HOU SHCDIV C (D7) Instructions d'installation et manuel de l'utilisateur - Page 2

Parcourez en ligne ou téléchargez le pdf Instructions d'installation et manuel de l'utilisateur pour {nom_de_la_catégorie} Bristan HOU SHCDIV C (D7). Bristan HOU SHCDIV C (D7) 2 pages.

Imprimer la page
General Cleaning
Bristan products are made from premium materials, with
hand polished, PVD, EPD or electroplated finishes.
Your shower should be regularly cleaned with warm water,
a mild pH-neutral liquid soap and polished with a soft cloth.
Any residues from soap, toothpaste, shampoos and shower
gels can cause blemishes if not rinsed off straight after use,
Household bleaches and cleaners contain harsh chemicals
and may damage the surface finish. Avoid using abrasive
cloths, scouring pads, scrub sponges, steel wool or anything
similar.
Wall Outlet Installation
Choose the location for the wall outlet
and create a 25-30mm hole in the wall.
Ensure your shower accessories have
enough reach from that position.
Finish the wall surface.
Servicing Intervals
To reduce the build up of lime scale and to
ensure this shower works to its maximum
performance we recommend this shower
is serviced every 6-12 months depending
on the hardness of your water.
Maintenance - Cartridge Cleaning
1
2
Remove the
handles.
IMPORTANT
Isolate the
water supply
before
Gently
starting!
remove the
concealing
plate from
2.5
mm
the wall.
4
5
Remove any O-rings and soak all
components in de-scaler and wash off
Reverse the installation steps,
in clean water. Examine all seals and
ensuring the temperature
replace if needed. Use WRAS
stop is aligned correctly.
approved silicon based grease
on all seals.
Operation
Off
Left
Outlet On
Increased
Temperature
With rear access
Fit the wall outlet,
ensuring the
washers are fitted
either side of
the wall.
Go to Step 6 in the
Installation Steps.
Without rear access
Screw the wall outlet into
Follow Step 6 in the
the 1/2" female connection,
Installation Steps, fitting a 1/2"
using a suitable thread sealant
female connection at the hole in
ensuring the rubber seal is fitted
the wall (not supplied).
to the back of the wall outlet.
3
23
mm
Unscrew the shrouds.
Remove the cartridges
and piston.
6
1
2
Increase
Temperature
3
Troubleshooting
Symptom
Partially closed isolation valve.
Right
Instantaneous water heater cycles on and off
as flow rate or pressure is too low.
Outlet On
Are the water supply pressures balanced?
No flow or
low flow rate
Hot or cold water being drawn off elsewhere
Decreased
causing pressure changes or instantaneous
Temperature
Airlock or partial blockage in the supply
Hot/Cold water supply has failed
Maximum
Water
Temperature
too Hot/Cold
Hot water temperature is less than 10°C
Outlet Water
above the required blend temperature
Temperature
too Hot/Cold
Instantaneous water not igniting because the
Instantaneous water not igniting because the
Only hot/
Inlet water supplies are reversed.
cold water
from Shower
Valve
This is normal for a short time after using the
Water
dripping
from shower
Shower does
not turn on
Mains water supply turned off.
Our Guarantee
Follow the
Temperature
Adjustment Steps
At Bristan, we want to make things as easy as possible for our customers. That's why we offer
if required.
solid guarantees on all our products, effective from the date of purchase, to give you peace of mind.
To start your free guarantee simply scan the QR code and register your product.
Alternatively visit www.bristan.com/register.
For any other queries, please call our Customer Service on 0330 026 6273
where our expert team of advisors will be able to offer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/service-centre/guarantees.
Bristan Group Ltd.
Decrease
Temperature
UK:
Bristan Group, B78 1SG.
EU:
Masco Europe S.à.r.l., 14 Rue Strachen
6933 Mensdorf, Luxembourg.
Cause
Head of water is below the
minimum distance required.
If pressures are unbalanced, a pressure reducing valve
should be used for optimum performance.
Do not use other water outlets when using the shower.
boiler temperature changes.
Flush through pipework and filters to ensure removal
pipework.
Check the hot and cold feeds. The shower will not
Maximum Water Temperature
Refer to the Temperature Setting section to set your
needs adjusting.
Flush through pipework and filters to ensure
Filter/pipe blockage
Installtion conditions outside
operating parameters.
Adjust hot water temperature or wait for water to
Increase water flow rate through the system. Refer to the
Maintenance section to clean/check the cartridge and filters
water flow rate is too low.
for any damage. Contact your boiler manufacturer.
Refer to the specification for system requirements.
Increase water pressure through the system.
water pressure is too low.
Check the water inlet connections are the correct way
around: Hot on the left, Cold on the right when viewed from
Flush through pipework and filters to ensure removal of
Filter/pipe blockage
This is caused by residual water tension, the build up of
shower.
If water continues to drip,
Remove cartridge and clean, refer to 'Maintenance' section
possibly due to the cartridge
Closed isolation valve.
Customer Service: +44330 026 6273
Web:
www.bristan.com
Email:
A Masco Company
Remedy
Open isolation valve.
Increase water flow rate or
pressure through system.
Refer to the specification for the
minimum distance required.
of debris and any airlocks.
work if either fails.
desired maximum temperature.
removal of debris and any airlocks.
Refer to the specification for the
minimum distance required.
reheat if a stored water system is used.
Contact your boiler manufacturer.
the front. Rework pipework as necessary.
debris and any airlocks.
water in the shower.
before starting any maintenance.
Open isolation valve.
Turn on mains water supply.