Centurion R5 Manuel d'installation rapide - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'installation rapide pour {nom_de_la_catégorie} Centurion R5. Centurion R5 2 pages. Rotary swing gate operator
Également pour Centurion R5 : Manuel d'installation rapide (19 pages), Manuel d'installation rapide (17 pages)

Imprimer la page

Centurion R5 Manuel d'installation rapide

ET THE

ONNECTING

ENGTH

Loosen the connecting arm slightly and move it to its fully retracted

position.

Open the gate ½ way.

Assemble the connecting arm to the gate bracket.

Now slowly push the gate to its closed position. (The drive arm will

turn, and the connecting arm will extend while doing so)

Check that the hinge points of the gate bracket, connecting arm and

motor output shaft are in a straight line as shown in Figure 8.

Carefully unhook the connecting arm from the gate bracket and

tighten lightly.

Check the gate opens and closes sufficiently by manually operating

the gate.

IF THE GATE OPENS TOO LITTLE

Lengthen the drivearm by 10 mm and readjust the connecting arm.

IF THE GATE OPENS TOO MUCH

Shorten the drivearm by 10 mm and readjust the connecting arm.

Fully tighten connecting arm.

Apply the warning decals supplied to either side of the gate frame.

LIGNMENT OF

INGE

OINTS

GATE LEAF IN CLOSED POSITION

NB. Hinge points must be in a

straight line when gates are closed

Figure 8 Align Gates

RIGGER

ONNECTIONS

For a detailed description of

terminal functions, refer to

DESCRIPTION OF TERMINAL

FUNCTIONS on page 45 of

the Installation Manual.

COM COM SOL 12V TRG IRB FRX LED PED LCK SET

SOLENOID

LOCK

RADIO RECEIVER

12V or 24V

IRB Tx

IRB RECEIVER

LOOP

LOOP DETECTOR

Figure 12 CP75 Controller Trigger Connections

ERFORM

NSTALLATION

ANDOVER

Explain to the user how to SAFELY operate the gate. (IM, page 51.)

LECTRICAL

WARNING

1. Always check that the circuit breaker in the electrical panel is in the

OFF position, and that all high voltage circuits (more than 42.4V) are

completely isolated from the mains supply before doing any work.

2. Ensure that all low voltage systems (Less than 42.4V) are suitably

protected from damage, by disconnecting all sources of power such

as chargers and batteries before doing any work.

3. All electrical work must be carried out according to the requirements

of all applicable local electrical codes.(It is recommended that a

licensed electrical contractor perform such work.)

ONNECT ALL

IRING

Connect all cables as required to the control card and battery

charger (See Figure 11 & 12). (IM page 48 & 49)

Check that the power source jumper is in the correct position. (PSU

or STD refer to IM page 27, Fig. 24)

Isolator

Box

To dwelling

Figure 9 Cabling Requirements

CP75 B

ASIC

ONTROLLER

ONNECTIONS

PSU

STD

STATUS

LIGHT

FUSE

(LED)

3A F/B

SLAVE FUSE 16A S/B

MASTER

-BATT+

SLAVE

LIGHT

SS1 SS2 SS3 COM COM SOL 12V

LIVE

NEUTRAL

AUXILIARY

SUPPLY

220V AC

MAINS IN

SLAVE

SS3

SS2

SS1

CP75A

SENSOR

MOTOR

6-WAY

CONNECTOR

CP84ER5V01

RED

BLACK

PURPLE

ORANGE

TO ORIGIN

TO COUNTER

SENSOR ON

3-WAY

SLAVE

CONNECTOR

MOTOR

ONLY FITTED IN DOUBLE SWING GATE SYSTEMS

Figure 11 CP75 Controller Connections

CABLE REQUIREMENTS

220V AC mains cable (3 core LNE

Radio receiver cable (3 core 0,5mm

0,5mm )*†, via mains isolator switch

multistranded).

Pedestrian key switch (if required) (2

core 0,5mm multistranded).

Low voltage 16V AC battery charger

supply (2 core 1,5mm )†.

Infrared beams or safety edge (if

required) (3 core 0,5mm

Intercom cable (n1 + 6 core) to

multistranded)

house.

Intercom cable (n2+2 core 0,5mm

Slave motor cable (if required) (3

multistranded) to gate station.

core 2,5mm + 3 core 0,5mm

multistranded).

n1 = number of cores required by intercom.

n2 = number of cores required by intercom.

* Increase cable thickness if pillar lights are to be installed.

† Screened cable is always recommended to provide better protection against lightning - earth one end

of screening.

ET UP THE

ATE

RIGIN

Release the manual override and close the gate(s).

Use the origin tool and line up marks as in figure 10. (IM page 28)

Open gate ½ way and unscrew the manual release mechanism.

(IM page 28).

ETTING THE

ATE

RIGIN

Setup Tool

Manual Release

Mechanism

Figure 10 Origin Setup

CP75 C

ONTROLLER

UNCTIONS

FEATURE

STATUS or COUNT

FEATURE

STATUS

COUNT

DESCRIPTION

VALUE

NUMBER

VALUE

Gate Limit Settings

See detailed instructions on page 29

Auto-close

OFF (Default)

15 seconds (Default)

Auto-close Time

1 Flash = 1 second

STANDARD (Default)

CONDOMINIUM

Mode of Operation

PIRAC

REVERSING

5 seconds (Default)

Pedestrian Auto-close

1 Flash = 1 second

120 seconds (Default)

Courtesy Light

1 Flash = 10 seconds

HIGH (Default)

Collision Sensitivity

MEDIUM

LOW

Auto-close Override

1 Flash = 1 second

3 second (Default)

Positive Close Mode

OFF (Default)

MODE 1

MODE 2

Preflashing

MODE 3

OFF (Default)

2 seconds (Default)

Preflash Time

1 Flash = 1 second

4 counts (Default)

Collision Counter

1 Flash = 1 count

Delay on slave opening

Delay on master closing

Leaf Delay Select

Delay on slave opening & master closing

Delay off (Default)

Leaf delay time /

2 seconds (Default)

1 Flash = 1 second

Solenoid Strike Time

Table 2 Controller Functions Menus and Submenus

NTO

ROGRAMMING

Remove all power. (IM page 28)

Fit the SET link.

Reapply power

ELECT EITHER

ASTER OR

Press and hold the TEST button, release after 1 flash of L1.

Then again, press and hold the TEST button, and release after 1 or

2 flashes of the STATUS LED. (1 Flash=master, 2 Flashes=slave)

(Installation Manual page 29)

ET THE

ATE

IMITS

Press and hold TEST until the gate is closed, and then release.

NB: THE GATE MUST CLOSE. IF IT OPENS :

Release the TEST button.

Swap the respective motor wires.

Press and hold TEST until gate is closed, and then

release.

Press and hold TEST until gate is open, and then release.

Press and release TEST (When setting up the MASTER gate, it will

close and then open to pedestrian. IM page 29).

If setting up the master gate, press and release TEST once more to

complete the setup (The MASTER gate will open fully, and the

SLAVE gate will move slightly).

ETTING

DDITIONAL

EATURES

Determine what features are required (See Table 2). (IM page 47)

Get into programme mode (as in Step 3), or continue from Step 5.

To select the Feature to Change: (IM page 31)

Press and hold the TEST button while monitoring L1:

Example of how to select the AUTOCLOSE feature:

The L1 light will flash once and pause,

Then flash twice and pause ...

At this moment release the TEST button to select feature

number 2. (L2 will turn off, and L1 will keep on flashing 2 times

and pausing to indicate that feature number 2 is selected).

NOTE: The STATUS of the Feature is not changed yet, the

feature has only been selected to be changed!

If an incorrect Feature is selected, then remove and re-

apply power and repeat the procedure.

To change the STATUS value of a Feature: (IM page 31)

Press and hold the TEST button while monitoring the

STATUS light:

(Continues from above example to set outoclose to ON status).

The L1 light will flash once and pause,

At this moment release the TEST button to give a

STATUS value of 1. The AUTOCLOSE feature has been set to

NOTE: Only after setting the STATUS, would the

AUTOCLOSE be turned ON.

(L2 will come back on, indicating that the STATUS has been

set.)

To change the COUNT value of a Feature: (IM page 31)

Press and hold the TEST button while monitoring the

STATUS light:

After a slight pause, the STATUS light will start flashing

regularly:

Flash (1), Flash (2), Flash (3), Flash (4), Flash (5),

Flash (6) ................ Flash (9), Flash (10).

At this moment release the TEST button to give a COUNT

value of 10. This could for example be the preflash time.

(L2 will come back on, indicating the COUNT value has

been set).

XIT

ROGRAMMING

ODE

Remove the SET link.

ODE

LAVE

ETUP

(

)

OPTIONAL