KitchenAid KECC501BAL0 Manuel d'instructions d'installation - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} KitchenAid KECC501BAL0. KitchenAid KECC501BAL0 9 pages. 30" and 36" electric built-in ceramic cooktops
Également pour KitchenAid KECC501BAL0 : Liste des pièces (5 pages)

Imprimer la page

Tools needed for

installation:

Electrical

requirements

extending from the fuse box or circuit

breaker box should be connected directly to

the junction box.

Locate the junction box to allow as

much slack as possible between

junction box and the cooktop so

that the cooktop can be moved if

servicing is ever necessary.

A U.L.- or C.S.A.-listed conduit

connector must be provided at

each end of the power supply

cable (at the appliance and at the

junction box).

Electrical Shock Hazard

Electrical ground is required on this

appliance.

Do Not ground to a gas pipe.

Do Not have a fuse in the neutral or

grounding circuit. A fuse in the

neutral or grounding circuit could

result in an electrical shock.

Check with a qualified electrician if

you are in doubt as to whether the

appliance is properly grounded.

Failure to follow these in instructions

could result in serious injury or death.

If codes permit and a separate grounding

wire is used, it is recommended that a

qualified electrician determine that the

grounding path is adequate.

IMPORTANT:

Save Installation Instructions

for electrical

inspector's use.

See back page for electrical connection

requirements for C.S.A.-certified models.

IA.I

A three-wire or four-wire, single

phase, 240-volt, 60-Hz, AC-only

electrical supply is required on a

separate, 40-ampere circuit, fused

on both sides of the line. A time-delay fuse

or circuit breaker is recommended.

The fuse

size must not exceed the circuit rating of the

appliance specified on the serial/rating

plate

located on the bottom of the cooktop.

THE COOKTOP MUST BE

CONNECTED

WITH COPPER

ICI

Wire sizes and connections

must

conform to the requirements

of the

. National Electrical Code

ANSVNFPA -

latest edition**, or

Canadian Electrical Code, C22.1- 1982,

and C22.2 No. 01982 (or latest edition)***

and all local codes and ordinances.

Copies of the standards listed may be obtained from:

'* National

Fire Protection

Association

Batterymarch

Park

Quincy,

Massachusetts

92299

** Canadian

Standard

Association

179 Rexdale

Boulevard

Rexdale

(Toronto),

Ontario

M9W 1 R3

Note: Warning below applies only to

cooktops installed in Canada.

Electrical Shock Hazard

Separate circuit breaker box must be

provided (not included with cooktop)

to complete

installation of this

appliance.

See wiring diagram, in this

installation instructions.

Failure to follow these instructions

could result in serious injury or death.

Electrical

connection

Electrical Shock Hazard

Electrical ground is required on this

appliance.

This appliance must be connected to

a grounded, permanent wiring

system or a grounding connector

should be connected to the

grounding terminal or wire lead on

the appliance.

Disconnect power to the junction

box.

Do Not connect to the electrical

supply until appliance is

permanently grounded.

Failure to do so could result in

electrical shock, serious injury, or

death.

This appliance is manufactured

with a frame

connected, green or bare grounding wire.

Connect the appliance cable to the junction

box through the U.L.- or C.S.A.-listed

conduit connector. Complete electrical

connection according to local codes and

ordinances.

Where local codes permit

connecting the frame-grounding

conductor to the neutral (white)

junction box wire:

cable from

power supply

connectors

black wires

U.L.- or C.S.A.- listed

conduit

connector

Where local codes Do Not permit

connecting the frame-grounding

conductor to the neutral (white)

junction box wire:

cable from power supply

junction

box

U.L;or

C.S.A.- listed

conduit

connector

cable from cooktop

Ungrounded neutral

Figure 2

1. Disconnect power supply.

2. Connect the flexible, armored cable from

the cooktop to the junction box using a

U.L.- or C.S.A.-listed

conduit connector.

Tighten screws on conduit connector.

3. Connect the two black wires together;

then connect the two red wires together

using twist-on connector. (See Figure 2.)

4. Connect the green or bare grounding

wire from the appliance cable to the

grounded wire in the junction box or other

grounded connector using twist-on

connector.

5. Put a twist-on connector on end of white

wire.

6. Contact a qualified electrician to assure

that grounding path is adequate.

7. Do Not ground to a gas supply pipe or

hot water pipe.

Do Not connect to

electrical supply until appliance is

permanently

grounded.

cable from cook-top

Grounded neutral

Figure 1

1. Disconnect power supply.

2. Connect the flexible, armored cable from

the cooktop to the junction box using a

U.L.- or C.S.A.-listed conduit connector.

Tighten screws on conduit connector.

3. Connect the green (or bare) appliance

cable wire with the neutral (white) wire in

the junction box using twist-on connector.

4. Connect the two black wires together;

then connect the two red wires together

with twist-on connector. (See Figure 1.)

The appliance should be connected

directly to the fused disconnect or

circuit breaker box through flexible,

armored or non-metallic

sheathed, copper

cable. The flexible, armored cable

Panel B