Brita 3-Way Water Filter Dispenser System Manuel d'utilisation - Page 10
Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Brita 3-Way Water Filter Dispenser System. Brita 3-Way Water Filter Dispenser System 13 pages. 3-way water filter dispenser
Imprimer la page
7
Technical data of the P 1000 cartridge
Operating pressure
Water intake temperature
operation
Ambient tem-
perature for
storage/transport
Nominal service fl ow
(acc. to DIN 18879)
Capacity up to carbonate hardness
8.5 °dH at setting "+"
Capacity from carbonate hardness
8.5 to 17 °dH at setting "++"
Pressure loss by nominal service fl ow
Empty fi lter cartridge volume
Weight (dry/wet)
Filter system
(fi lter head with fi lter
cartridge)
Dimensions
Filter cartridge
(Width/Depth/
Height)
Installed dimensions
(vertical installation
with wall mounting
bracket)
Operating position
Water inlet connection
Water outlet connection
8
Troubleshooting
A No water fl ow
Cause:
Water intake closed.
Troubleshooting:
Open the water intake at the upstream shut-off
valve or by closing the locking handle (3) on the
fi lter head. Check hoses for kinks.
B No or low water fl ow in spite of open water intake
Cause:
Mains pressure too low.
Troubleshooting:
Check mains pressure. If the fault continues,
check the fi lter system and fi lter cartridge and
replace if necessary. Check hoses for kinks.
2 bar to max. 8.6 bar
4°C to 30°C
4°C to 40°C
–20°C to 50°C
60 L/h
1000 L
500 L
0.2 bar
1 L
For models WD 3030 and WD 3040 only
1.0 kg/1.4 kg
117 mm/108 mm/265 mm
108 mm/108 mm/259 mm
137 mm/130 mm/265 mm
Horizontal and vertical
G3/8"
G3/8"
Cause:
Filter head not mounted in direction of water
fl ow / hoses wrongly connected.
Troubleshooting:
Dismantle fi lter head and hoses and install in
direction of water fl ow (chapter 3.4).
C Leak
Cause:
Screwed connections not fi tted correctly.
Troubleshooting:
Check mains pressure. Check all screwed
connections and mount as described in
chapter 3.4.
D Incorrect display or incorrect settings on the electronic
cartridge exchange indicator with display
Cause:
Buttons pressed in wrong order or wrong
buttons pressed.
Troubleshooting:
Press and hold the RESET button for
8 seconds.
These models have an aerator with two integrated outlets. The
Inner one is for BRITA fi ltered water, the outer area for hot and cold
water. As with every tap aerator, there can be lime scale build up
in the outer area. Therefore it is recommended to clean the aerator
on a regular basis. For cleaning: Unscrew the cap on the end of the
dispensers neck. The aerator is connected to a silicon hose. Detach
it carefully and clean the aerator (e.g. with vinegar). After cleaning
connect the long, thin part on the back of the aerator carefully with
the silicon hose. Place the cap over the aerator and screw it tight.
Make sure that the gasket in the cap is seated correctly. When
installed correctly there should not be any leaks whilst running hot,
cold or BRITA fi ltered water.
If you want to replace the aerator with a new one, you can order
it from BRITA. You can fi nd the contact details for your BRITA
customer service team next to your country code on the back of
this booklet.
(fi g. 10)
9
ENGLISH