KitchenAid KECC502GBL1 Manuel d'instructions d'installation - Page 3
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} KitchenAid KECC502GBL1. KitchenAid KECC502GBL1 7 pages. 30" (76.2 cm) and 36" (91.4 cm) electric built-in ceramic cooktops
Également pour KitchenAid KECC502GBL1 : Liste des pièces (3 pages)
Imprimer la page
Electrical
requirements
if codes permit and a separate
ground wire is
used, it is recommended
that a qualified
electrician
determine
that the ground path is
adequate.
Do Not ground to a gas pipe.
Check with a qualified
electrician
if you are
not sure the cooktop
is properly
grounded.
Do Not have a fuse in the neutrat or ground
circuit.
iMPORTANT:
Save _nstaliat{on
instructions
for electrical
inspector's use.
A
E A three-wire or four=wire, single phase,
240=volt, 60=Hz, AC=only electrical supply is
required on a separate, 40=ampere circuit, fused
on both sides of the line. A time=delay fuse or
circuit breaker is recommended. The fuse size
must not exceed the circuit rating of the
appliance specified on the model/serial
rating
plate located on the bottom of the cooktop.
m THE COOKTOP MUST BE
CONNECTED WiTH COPPER WiRE ONLY
C
E Wire sizes and connections must conform
to the requirements of the National Electrical
Code ANSJ/NFRA 70 = latest edition **, or CSA
Standards C22.1=94, Canadian Electrical Code,
Part 1 and C22.2 No. 0=M91 = latest edition ***
and aH local codes and ordinances.
E The cooktop should be connected directly
to the fused disconnect or circuit breaker box
through flexible, armored or non=metallic
sheathed, copper cable. The flexible, armored
cable extending from the fuse box or circuit
breaker box should be connected directly to the
junction box.
E
m Locate the junction box to allow as much
slack as possible between the junction box and
the cooktop so that the cooktop can be moved if
servicing is ever necessary. Do Not cut the
conduit.
Fm
A U.L.= or C.S.A.=listed conduit connector
must be provided at each end of the power
supply cabJe (at the cooktop and at the junction
box).
Copies of the standards listed may be obtained from:
** National
Fire Protection
Association
Batterymarch
Park
Quincy, Massachusetts
02269
*** Canadian Standard
Association
178 Rexda[e Boulevard
atobicoke
(Toronto), Ontario
MgW 1R3
Electrical
connection
Electrical
Shock Hazard
Turn power supply off before connecting
wires.
Use 8-gauge solid copper wire.
Electrically
ground cooktop.
Failure to follow these instructions can
result in death, fire, or electrical
shock.
This cooktop
must be connected
to a
grounded,
metallic
permanent
wiring
system
or a ground connector
should
be connected
to the ground terminat
or wire lead on the
cooktop.
This cooktop is manufactured with a frame
connected, green or bare ground wire. Connect
the cooktop cable to the junction box through the
U.L= or C.S.A.=iisted conduit connector.
Complete electrical connection according to local
codes and ordinances.
AR
Where local codes permit connecting
the frame=ground
conductor
to the neutral
(white} junction
box wire: (Not used for
Canadian
installations).
cable from power supply
red wires
"unction
box
twist-on
connectors
black wires
U.L- or C.S.A.- Hsted
conduit connector
Grounded
neutral
Figure
1
1. Disconnect
power supply.
2. Connect the flexible, armored cable from the
cooktop to the junction box using a U.L= or
C.S.A.=[isted conduit connector. Tighten screws
on conduit connector.
3. Connect the green (or bare) appliance cable
wire with the neutral (white) wire in the
junction box using twist=on connector.
4. Connect the two black wires together; then
connect the two red wires together with twist=
on connector. (See Figure 1.)
m Where [ocat codes Do Not permit
connecting
the frame=ground
conductor
to
the neutral (white} junction box wire: (Used
for all Canadian
installations}.
cable from power supp}y
red
bare
or green
_
w_res
cable from cooktop
_
junction
box
i
_hite
wire
t
I
_'-,twist-on
connector
,,J_, black wires
U.L.= or C.S.A.- listed
conduit
connector
Ungrounded
neutral
Figure
2
Now start...
With cooktop
in kitchen.
Excessive Weight Hazard
Use two or more people to move and instal[
cooktop.
Failure to do so can result in back or other
injury.
m Remove the shipping materials and tape
from the cooktop. Remove the hardware package
from inside the literature bag=
m Insert the cooktop into the countertop.
Center the cooktop in the cutout. Check that the
front of the cooktop is parallel to the front edge of
the countertop. Check that all required
clearances are met.
If cooktop is not properly positioned, lift the
cooktop off the countertop to make adjustments.
countertop
slot
/
screw
damp
assembly
damp
tab
burner
box
3E
Insert one clamp tab through each slot
located on sides of the burner box.
Note: [f installing cooktop over a built=under oven,
Do Not fasten cooktop to countertop with
cramps. Cooktop will then be easy to remove if
servicing is ever required.
4m
Secure cooktop to countertop by hand=
tightening each screw; then use a screwdriver to
tighten each screw 1 to 1=1/2 more turns. Do Not
overtighten screws.
5m
Make electrical connection. (See
"Electrical requirements" and "Electrical
connection" sections, Panel B.)
Turn on power supply.
7=_
Depending on your model, push in and
turn each control knob to the "Hi" position or
touch "ON" and turn each control knob to the "HI"
position. Check the operation of the cooktop
elements and indicator lights.
Pane[ B
1. Disconnect
power supply.
2. Connect the flexible, armored cable from the
cooktop to the junction box using a U.L= or
C.S.AMisted conduit connector. Tighten screws
on conduit connector.
3. Connect the two black wires together; then
connect the two red wires together using twist=
on connector. (See Figure 2.)
4. Connect the green or bare ground wire from
the appliance cable to the grounded wire in
the junction box or other grounded connector
using twist=on connector.
5. Put a twist=on connector on end of white wire.
To get the most efficient
use from
your
new cooktop,
read your
Use and Care Guide.
Keep
Installation
instructions
and Guide
close
to cooktop
for easy reference.