IKEA STJARNSTATUS 204.621.51 Instructions d'installation
Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} IKEA STJARNSTATUS 204.621.51. IKEA STJARNSTATUS 204.621.51 3 pages.
Imprimer la page
STJÄRNSTATUS
WARNING
To avoid electric shock, which can cause death or severe personal injury, do
not connect your refrigerator to an electrical power source until you have
completed Step 2 of these instructions.
NOTE
If you need to remove the doors to get your refrigerator into the house, please refer to Section
3: "Door Removal/Installation", or, for more detailed instructions, "Removing Doors" in the Use &
Care Guide. These installation instructions are provided only as a possible customer option. IKEA
recommends that you use a service or kitchen contracting professional to install your refrigerator.
IMPORTANT
CAUTION
If you are installing your refrigerator
• Shifting the refrigerator from side-to-side
without connecting it to a water supply,
may damage flooring.
make sure the ice maker's power switch
• Do not block the toe grille on the lower
is turned Off (see Use & Care Guide for
front of your refrigerator. Sufficient air cir-
more details).
1
culation is essential for proper operation.
Preparing For Installation
Be sure to coordinate site preparation and installation with your kitchen contractor.
Include these minimum guidelines in your site preparation:
•
Choose a place near a grounded electrical outlet.
•
Do not use an extension cord or an adapter plug.
•
Avoid direct sunlight and close proximity to a range,
dishwasher or other heat source.
•
Floor should be level and able to
support a fully loaded refrigerator.
•
The refrigerator's Ice Dispenser
requires water supply access.
•
Plan for easy access to counter tops
when removing food.
•
For complete access to drawers and
freezer baskets, doors must be able to fully open.
•
Load refrigerator from side of cabinet only.
•
Do not run retaining straps over handles nor overtighten
straps.
•
Never use refrigerator handles to move the refrigerator.
Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections:
Sides & Top:
/
inch / Rear: 1 inch
2
3
8
Connect Water Supply
Before Installing The Water Supply Line, You Will Need:
•
Basic Tools: adjustable wrench, flat-blade screwdriver, and
Phillips™ screwdriver.
•
Access to a household cold water line with water pressure
between 30 and 100 psi. A water supply line made of ¼
inch (6 mm) OD, copper or braided, flexible stainless steel
tubing. To determine the length of tubing needed, measure
the distance from the ice maker inlet valve at the back of the
refrigerator to your cold water pipe. Then add approximately
7 feet, so the refrigerator can be moved out for cleaning.
•
A shutoff valve to connect the water supply line to your
household water system. DO NOT use a self-piercing type shutoff valve.
•
A compression nut and ferrule (sleeve) for connecting a copper water supply line to the ice maker
inlet valve.
CAUTION
To Avoid Property Damage:
• Copper or Stainless Steel braided, flexible tubing is recommended for the
water supply line. Water supply tubing made of ¼ inch (6 mm) plastic is not
recommended to be used. Plastic tubing greatly increases the potential for
water leaks, and the manufacturer will not be responsible for any damage if
plastic tubing is used for the supply line.
• Do not reuse compression fitting or use thread seal tape.
• DO NOT install water supply tubing in areas where temperatures fall below freezing.
• Chemicals from a malfunctioning softener can damage the ice maker. If the
ice maker is connected to soft water, ensure that the softener is maintained
and working properly.
(833) 337-4006
Refrigerator Installation Instructions
To Connect Water Supply Line To Ice Maker Inlet Valve
1. Disconnect refrigerator from electric power source.
2. Place end of water supply line into sink or bucket. Turn ON water
supply and flush supply line until water is clear. Turn OFF water
supply at shutoff valve.
3. Remove plastic cap from water valve inlet and discard cap.
4. If you use copper tubing - Slide brass nut, then ferrule (sleeve)
onto water supply line. Push water supply line into water valve
inlet as far as it will go (¼ inch). Slide ferrule (sleeve) into valve
inlet and finger tighten nut onto valve. Tighten another half turn
with a wrench; DO NOT overtighten. See Figure 1.
If you use braided, flexible stainless steel tubing - The nut is
already assembled on the tubing. Slide nut onto valve inlet and
finger tighten nut onto valve. Tighten another half turn with a
wrench; DO NOT overtighten. See Figure 2.
5. With steel clamp and screw, secure water supply line
(copper tubing only) to rear panel of refrigerator as shown.
6. Coil excess water supply line (copper tubing only), about 2½
turns, behind refrigerator as shown and arrange coils so they do
not vibrate or wear against any other surface.
7. Turn ON water supply at shutoff valve and tighten any connec-
tions that leak.
8. Reconnect refrigerator to electrical power source.
9. To turn ice maker on, lower wire signal arm (freezer ice maker)
or set the ice maker's On/Off power switch to the "ON" position
(fresh food ice maker).
NOTE
NOTE
Check with your local building authority for recommendations on
water lines and associated materials prior to installing your new
Please call (833) 337-4006 if
refrigerator. Depending on your local/state building codes, IKEA
recommends for homes with existing valves its Smart Choice 6
you need assistance with this
installation.
ft. Stainless Steel Refrigerator Water Line Kit 5304490728 and
for homes without an existing valve, Frigidaire recommends its
Smart Choice 20 ft. Copper Refrigerator Water Line Installation
CAUTION
Kit 5304490717 (with a self-tapping saddle valve). Please refer
to www.frigidaire.com for more information or call
(833)337-4006.
Room temperatures below
55°F (13°C) or above 110°F
(43°C) will impair cooling
3
ability of your refrigerator's
Door Removal/Installation
compressor.
Removing the Doors:
WARNING
Turn off power to your refrigera-
tor, by unplugging the power cord
from the wall outlet.
WARNING
1. Remove refrigerator doors' top hinge covers.
2. Disconnect the harness by depressing the latch, and pulling apart.
To avoid electric shock,
3. Detatch the water tube from the connector located behind the refrigerator,
which can cause death or
the connector releases when you press inward on the connectors outer
severe personal injury, dis-
sleeve. Pull the water tube out toward the front of the unit.
connect the refrigerator from
electrical power before con-
4. Open the refrigerator doors to a 90° angle. Remove 2 screws from the top
necting a water supply line
hinge. Lift and remove door from lower hinge. Be sure doors are set aside
in a secure position where they cannot fall and cause damage to the doors
to the refrigerator.
or the handles.
5. Unscrew the 3 lower hinge screws and remove the hinge.
IMPORTANT
Open the refrigerator doors to a 90° angle before removing or installing the doors on the lower hinges.
To reinstall the refrigerator doors:
1. Replace the lower hinges by screwing in place.
2. Hold the door at ~90°, and drop the closure mechanism down into the lower hinge pin. Then rotate
it slightly in either direction until the door/mechanism falls down into place. Install the top hinge,
thus locking the door in place.
3. Insert the water line into the top section of the unit and insert into the connector.
4. Connect the harness at the top of the hinges.
5. Replace the top hinge covers.
4
Steel
Plastic Water
Clamp
Tubing to Ice
Maker Fill
Brass
Compression
Tube
Nut
Removing Freezer Drawer:
Ferrule
1. Remove 4 hex head drawer screws.
(Sleeve)
2. Lift up drawer to remove.
Copper
water line
Water Valve
Bracket
Valve Inlet
Water Valve
Copper water line
from household
water supply
(Include enough tubing in loop
to allow moving refrigerator out
for cleaning.)
Figure 1
Plastic Water Tubing
Steel
to Ice Maker
Clamp
Fill Tube
Braided
Flexible
Stainless
Steel
Water Line
Water Valve
Bracket
5
Valve Inlet
Guidelines for final positioning of refrigerator:
Water Valve
•
6 ft (1.8 Meters) Braided flexible
•
stainless steel water line from
household water supply.
•
Figure 2
Most of these conditions can be met by raising or
(Include enough tubing in loop to allow
lowering the adjustable front rollers.
moving refrigerator out for cleaning.)
To level the cabinet using the front rollers (if
necessary):
1. Slightly open freezer drawer if the toe grill is installed.
2. Make initial cabinet adjustments by using the front
NOTE
You will be pulling approximately 5 feet of water
tube from the back of the refrigerator. Use care
while pulling the water tube from the unit to
ensure not kinking the tube.
3. Ensure both doors are bind-free
Top View
Top View
Cabinet
Cabinet
6
90˚
IKEA uses packing foam and tape to secure the internal parts of your refrigerator for shipping. Once
the refrigerator is in position, you can remove this material.
What's Next?
Congratulations! You are ready to begin enjoying your new IKEA refrigerator.
•
•
7
Doors
□ Handles are secure and tight
□ Door seals completely to cabinet on all sides
□ Fresh food doors are level
Leveling
□ Refrigerator is level, side to side and tilted ¼
□ Toe grille is properly attached to refrigerator
□ Cabinet is sitting solid on all corners
This document should only be removed
by the customer after installation.
Removing & Replacing Freezer Drawer
Replacing Freezer Drawer:
1. Extend the Freezer slides from unit.
2. Carefully align support pin with hooks
on end of freezer slides and then lower
DO NOT
Remove
freezer door onto slides.
DO NOT
Other
3. Replace the 4 hex head screws that
Loosen
Screws
or
secure the slides to the door (2 on
Remove
each side) and tighten.
These 3
Hex
Screws
Remove
Hex Head
Drawer Screw
CAUTION
Drawer is heavy. Use caution when lifting.
NOTE
To locate the pin, look inside the drawer and the pin is next to the door liner and the slides. Not all
parts are shown in the illustration.
Level Refrigerator & Refrigerator Door Alignment
4. After unit is leveled, lower anti-tip leg
using a 3/8 inch socket wrench until it
All four corners of cabinet must rest firmly on floor.
firmly contacts the floor.
The front should be slightly elevated (to ensure that
5. Install toe grille by fitting into place.
doors close and seal properly).
Doors should align with each other and be level.
To make final door height
adjustments (if necessary):
1. Open freezer drawer to make lower
hinge visible.
2. Insert 6mm Allen wrench into the
shaft of the lower hinge.
3. Adjust the height by turning clockwise
Lift the toe grille and gently pull forward.
or counterclockwise. Turning
clockwise will lower the door. Turning
roller height adjusting screws. Use a 3/8 inch socket
counterclockwise will raise the door.
wrench to turn the adjustment
Raise
Default setting is to the lowest height
screws (1 per side).
when you receive your appliance.
Anti-tip
To raise: turn adjustment screw
Leg
clockwise.
Lower
To lower: turn adjustment screw
counterclockwise.
with their seals touching the cabi-
net on all four sides and that cabinet is stable.
Remove Internal Shipping Materials
For important safety instructions and to learn how to operate your refrigerator, please read the
entire Use & Care Guide.
You may want to start with the "Normal Operating Sights & Sounds" section of the Guide to learn
what to expect during typical operation.
Installation Check List
Ice Maker
□ House water supply connected to refrigerator
□ No water leaks present at all connections
□ Ice Maker is turned ON.
Final Checks
□ Shipping material removed
inch (6 mm) front to back
□ Fresh Food and Freezer temperatures set
Electrical Power
□ House power turned on
□ Refrigerator plugged in
AA-2194805-2
P/N: A19100501
Pin
Hook
Raise
Door