KitchenAid KGCT305BWH0 Manuel d'instructions d'installation - Page 4
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} KitchenAid KGCT305BWH0. KitchenAid KGCT305BWH0 9 pages. 30” (76.2cm) and 36” (91.4cm) gas sealed burner glass cooktops
Imprimer la page
Use a brush and liquid detergent
to test all gas connections for
leaks. Bubbles around
connections
will indicate a leak. If
grate
a leak appears, shut off gas valve controls and
adjust connections.
Then check connections
again. NEVER TEST FOR GAS LEAKS WITH
A MATCH OR OTHER FLAME.
Clean all
detergent solution from cooktop.
burner box
m-l
Place
burner
n
grates over
-
burners and
caps.lnstall
control knobs
on valve stem-s.
Install the pressure regulator with the
arrow on the regulator pointing up
toward unit and in a position where
you can reach the access cap.
Electronic Ignition System-
initial lighting
Cooktop burners use electronic igniters in place
of standing pilots. When the cooktop control
knob is turned to the "HI" position, the system
q
4
Insert cooktop into countertop
opening. Center the cooktop in the
cutout. Check that front edge of
cooktop is parallel to front edge of
countertop.
Check that all required clearances
are met. Use a pencil to outline the rear of the
cooktop on the countertop.
Remove the cooktop
from the cutout and place upside down on a
protected surface.
Attach the mounting brackets to each
side of the burner box with the 5/l 6"
(0.80cm) screws. Do Not tighten the
screws. Turn the mounting brackets
so each is under the burner box.
Check that cook-top is parallel to front
edge of countertop.
Lift entire cooktop
to make adjustments
so the foam
sealing strip can seal properly.
Personal
Injury Hazard
Do Not over-tighten
screws.
Overtightening
screws could cause
personal
injury or product
damage.
glass cooktop
\
countertop
I
mounting
5/16"
(0.8Ocm)clamp
bracket
bracket screw
Ll
7
Rotate mounting brackets away from
burner box. Tighten the mounting
brackets to the burner box. Insert the
2-l/2" (6.4cm) clamping screws into
the mounting brackets. Use a screwdriver to
tighten screws against the underside of
countertop.
creates a spark to light the burner. This sparking
continues until the burner ignites.
Fire Hazard
Do Not make connection
too tight.
The
regulator
is die cast.
4
seconds.
3/8" (0.95cm)
nipple
flexible connector
3/8" (0.95cm) nipple If burners do not light
+
properly, turn control
knob to the "OFF" position. Check that burner
El
cao is in the orooer position. Check that power
(0.95cm) adapt&rs
t
manual shutoff valve
pressure
regulator
'All connections
must be wrench-tightened.
.&bply cord is piugged in and that the circuit
breaker or house fuse has not blown. Check that
the shutoff valve is in the "ON" position. Checsc
operation again.
If a burner does not light at this
point, contact your KitchenAid dealer for
assistance.
m-l
Assemble the flexible connector
from the gas supply pipe to the
pressure regulator in order:
-
manual shutoff valve, 3/8"
(0.95cm) nipple, 3/8" (0.95cm) adapter, flexible
connector, 3/8" (0.95cm) adapter, and 3/8"
(0.95cm) nipple.
Use pipe-joint compound made for
use with NATURAL and L.P. gas
to seal all gas connections.
If
flexible connectors are used, be
certain connectors are not kinked.
shutoff valve
Open the shutoff
valve in the gas supply line. Wait a
few minutes for gas to move
through the gas line.
Fire Hazard
Do Not use an open flame to test for leaks
from gas connections.
Checking
for leaks with a flame may
result in a fire or explosion.
116.
Check each cook-top
burner for proper flame.
The small inner cone
-
should have a very
distinct blue flame approximately
l/2"
(1.3cm) long. The outer cone is not as
distinct as the inner cone.
Push in and turn each control
knob to the "LO" (or simmer)
setting. The "LO" setting of each
burner has been factory set to the
lowest setting available to provide reliable
reignition of the burner. If it does not stay lit on
the "LO" setting, contact your KitchenAid dealer
for assistance.
-
To get the most efficient use
from your new cooktop, read
your KitchenAid Use and Can!
Guide. Keep Installation
Instructions
and Guide close
to cooktop for easy reference,.
-
L.P. gas I
conversion
No attempt shall be made to convert the
appliance from the gas specified on the
serial/rating
plate for use with a different gas
without consulting the servicing gas supplier.
Conversion
must be done by a service
technician. Conversion
Kit No. 4173627 is
available from your KitchenAid dealer or
authorized parts distributor.
Panel C