KitchenAid KGCV465MSS03 Manuel d'instructions d'installation - Page 6

Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} KitchenAid KGCV465MSS03. KitchenAid KGCV465MSS03 20 pages. 36" pro line series commercial style cooktop

Imprimer la page

L.Po Gas:

No attempt shall be made to convert the

cooktop from the gas specified on the

model/serial rating plate for use with a

different gas without consulting the

serving gas supplier. Conversion must be

done by a qualified service technician. To

convert to L.R gas, use L.R gas

conversion kits part no. 8285442 and

8285443. The parts for these kits are in

the literature package supplied with

cooktop.

mProvide a gas supply line of 3/4"

rigid pipe to the cooktop location. A

smaller size pipe on long runs may result

in insufficient gas supply. Pipe-joint

compounds, suitable for use with L.R gas,

must be used. With L.R gas, piping or

tubing size can be 1/2" minimum. L.R gas

suppliers usually determine the size and

materials used on the system.

If local codes permit, use a flexible

stainless steel tubing gas connector,

design-certified by AGA or CSA

International, to connect the cooktop to

the rigid gas supply line. 5/8" diameter line

is recommended. Do Not kink or damage

the flexible connector when moving the

cooktop. The pressure regulator has 1/2"

female pipe threads. You will need to

determine the fittings required, depending

on the size of your gas supply line, flexible

metal connector and shutoff valve.

shutoff value on

"open" positU

gas supply

line

EThe supply line shall be equipped

with an approved shutoff valve. This valve

should be located in the same room as

the cooktop and should be in a location

that allows ease of opening and closing.

Do Not block access to the shutoff valve.

The valve is for turning on or shutting off

gas to the appliance.

mlf rigid pipe

is used as a gas

_r_

supply line, a combination of pipe

IJI

fittings must be used to obtain an in-line

connection to the cooktop. All strains

must be removed from the supply and

fuel lines so cooktop will be level and in

line.

raTheregulator must be checked at a

minimum 1=inch(2.5 cm) water column

above the set pressure. The inlet pressure to

the regulator should be as follows for

operation and checking the regulator setting:

NATURAL GAS:

Set pressure 5 inches (12.7 cm)W.C.

Supply pressure 7-14 inches (17.8 cm

to 35,5 cm) W,C. maximum.

L.P. GAS:

Minimum pressure 10 inches (25.4 cm)

W.C.

Supply pressure 14 inches (35,8 cm)

W.C,

E Line pressure testing:

Testing above 1/2 psi (3.8 kPa) or

14 inches (35,5 cm) W,C. (gauge)

The cooktop and its individual shutoff

valve must be disconnected from the gas

supply piping system during any pressure

testing of that system at test pressures

greater than 1/2 psig (3.5kPa).

Testing below 1/2 psi (3.5 kPa) or

14 inches (35.5 cm) W,C, (gauge) or

lower

The cooktop must be isolated from the

gas supply piping system by closing its

individual manual shutoff valve during any

pressure testing of the gas supply piping

system at test pressures equal to or less

than 1/2 psig (3.5 kPa).

Electrical

Shock Hazard

Plug into a grounded

3=prong

outlet.

Do not remove ground prong.

Do not use an adapter.

Failure to follow these

instructions

can result in death,

fire, or electrical

shock.

If codes permit and a separate ground

wire is used, it is recommended

that a

qualified electrician

determine that the

ground path is adequate,

Check with a qualified electrician

you are not sure whether the cooktop

is properly grounded,

Do Not ground to a gas pipe.

A 120-volt, 6O-Hz, AC-only, 15-ampere,

fused electrical supply is required. A

time-delay fuse or circuit breaker is

recommended. It is recommended that a

separate circuit serving only this

appliance be provided.

Electronic ignition systems operate within

wide voltage limits, but proper ground and

polarity are necessary. In addition to

checking that the outlet provides 120-volt

power and is correctly grounded, the

outlet must be checked by a qualified

electrician to see if it is wired with correct

polarity. A wiring diagram is provided on

the last page of these instructions.

Important: This cooktop is equipped with

an electronic ignition system that will not

operate if plugged into an outlet that is

not properly polarized.

This appliance, when installed, must be

electrically grounded in accordance with

local codes or, in the absence of local

codes, with the current CSA standard

C22.1. Canadian Electrical Code Part 1".

Recommended

ground

method

For your personal safety, this cooktop

must be grounded. This cooktop is

equipped with a 3-prong ground plug. To

minimize possible shock hazard, the cord

must be plugged into a mating 3-prong

ground-type outlet, grounded in

accordance with the National Electrical

Code ANSI/NFPA 70 latest edition** or

Canadian Electrical Code (CSA)* -- and

local codes and ordinances. If a mating

outlet is not available, it is the personal

responsibility and obligation of the

customer to have a properly polarized

and grounded, 3-prong outlet installed by

a qualified electrician.

3=prongpolarized

ground=type outlet

roondp,og \

I11 ground

power

/i'J

prong

supply cord

Copies of the standards listed above may be

obtained from:

* CSA International

8501 East Pleasant Valley Rd.

Cleveland,

Ohio 44131-5575

** National

Fire Protection

Association

One Batterymarch

Park

Quincy, i',_assachasetts 02265