KitchenAid KGCV566RMT01 Manuel d'instructions d'installation - Page 5
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} KitchenAid KGCV566RMT01. KitchenAid KGCV566RMT01 17 pages. Gas built-in cooktops
Imprimer la page
Ebctronic i gnition systems o perate
withinwidevoitage iimits,butproper
ground andpoiarity arenecessary. In
addition to checking thattheoutlet
provides 1 20-voit power andiscorrecdy
grounded, theoutlet m ustbechecked b y
a qualified eiectrician to seeif it iswired
withcorrect p ohrity.Awiringdiagram is
provided intheiiterature p ackage,
iMPORTANT:
Thisrange is equipped w ith
aneiectronic i gnition system thatwHi n ot
operate i f piugged intoanoutlet t hatis
notproperly polarized,
Thisappliance, wheninstalled, mustbe
electrically grounded i naccordance with
local c odes o r,intheabsence o f local
codes, withthecurrent C SA standard
C22,1, Canadian Electrical Code Part 1 ,
Recommended
ground method
Foryourpersonal safety, thiscooktop
mustbegrounded.This cooktop is
equipped w itha3oprong g round plug.To
minimize possible s hock hazard, thecord
mustbeplugged intoa mating 3-prong
ground-type outlet, g rounded i n
accordance withtheNational Electrical
Code ANSI/NFPA 70latest e dition __or
Canadian Electrical Code (CSA) ×,x_ --
andlocal c odes andordinances, Ifa
mating outlet i s notavailable, it isthe
personal responsibility andobligation of
thecustomer to have a properly
polarized a ndgrounded, 3=prong outlet
installed bya qualified e lectrician,
3-prong polarized
ground-type
outlet _
"--a_
3-prong
ground p lug
power
supply c ord
Now start,,,
With cooktop
in kitchen.
Excessive
Weight
Hazard
Use two
or more
people
to move
and
install
range.
Failure
to do so can result
in back or
other
injury.
o Remove foam shipping
blocks and
tape from cooktop,
Untape power supply
cord,
o Remove
pressure
regulator,
hardware
package,
burner
grates,
burner
caps,
clamp
brackets,
and 2ol/2"(6,4
cm)
clamp
screws,
from
shipping
package,
attachment
screws
for optional
front
_...burner
box
and back location
bottom
attachment
screw
bracket (end
_
locations
recommended)
a
o if installing
before
the cooktop
is placed
into
cutout:
o Place
the cooktop
upside
down
on a
protective
surface
(blanket,
pad).
Glass
cooktops
only:
Remove
foam
strip
from
literature
package.
Apply
foam
strip
around
bottom
of cooktop
flush
with
edge.
o Remove
the attachment
screws
for the
bracket
locations
selected
from
the
bottom
of the burner
box.
o Use bracket
mounting
holes
that
will
allow
the clamp
screws
(see Step
4) to
contact
the countertop
bottom.
Attach
brackets
as
shown
then
rotate
brackets
so that
they
do not extend
beyond
edge
of burner
box.
oTighten
screws
just
enough
to hold
brackets
in place
when
cooktop
is
turned
over
and put into
cutout.
oTurn
the cooktop
right
side up and
carefully
place
into the cutout.
IMPORTANT:
Check that the front
edge
of
the cooktop
is parallel
to the front
edge
of the countertop,
Lift entire
cooktop
up
from
cutout
when
repositioning
cooktop
to prevent
scratching
the countertop,
o Loosen
the screws
or nuts,
rotate
the
brackets
so that
they
extend
beyond
edge
of the burner
box,Tighten
screws
securely_
Copies of the standards
listed may be
obtained
from:
_National
Fire Protection
Association
One Batteryrnarch
Park
Quincy, Massachusetts
02269
_*CSA
International
8501 East Pleasant \/alley Rd.
Cleveland,
OH 44131-5575
"U" shaped spring
clip or small
diameter
hole
3o
Two
clamp
brackets
are provided
to clamp
the cooktop
to the countertop,
Install
the clamp
brackets
on each end of
the burner
box bottom,
Optional:
If
cabinet
construction
does
not provide
clearance
for installing
brackets
at burner
box
ends,
install
the brackets
on the front
and back of the burner
box bottom,
The brackets
may
be installed
before
(see
Step
3a) or after
(see Step
3b) the
cooktop
is placed
into
the cutout,