KitchenAid KDC-18 Manuel d'instructions d'installation - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} KitchenAid KDC-18. KitchenAid KDC-18 6 pages. Kd-18 series built-in dishwasher

KitchenAid KDC-18 Manuel d'instructions d'installation
0
3
DRAIN
SYSTEM
(Cont.)
--'-
34'
-
u-------y
-!
I
MIX.
(57*~01R0)
MIX.
(57*~01R0)
---00" -00"
MAX.
IN RESRICIED
- -
MAX.
IN RESRICIED
- -
CODC AREA)
CODf
AREA)
i
P-IK)t,
t-u
m
--
FIG.
5
NOTE:
Drain
Hose #B-240385
may be used
to connect
dishwasher
with disposer unit, or
to sink
drain
using Tee P-83095
or elbow
M-66693
(available as accessories).
CAUTION:
Make sure drain
hose does not
touch any electrical
components
or terminaF
Drain
hose must
withstand
hot
water
and
detergent
and can be obtained
from a plumb
ing hardware or automotive
supply outlet.
Other
accessories
available
from
your
dealer or distributor
are:
Top Kits
Rinse Agent Kit
Front Trim
Kit
Side Panel Kits
Front Panel Kits
0.
4
ELECTRICAL
SUPPLY
LINE
Before
setting
dishwasher
in
place,
run
individual
15 amp. minimum
branch
circuit
with
grounded
electrical
cable.
(A, Fig. 6)
shows
routing
methods
for
the
electrical
supply
line
hook-up
to
the
KitchenAid
dishwasher.
CAUTION:
No other
outlets
or
appliances should be on this circuit
JUNCIION
DOX
FIG. 6
FINAL
INSTALLATION
0
1
POSITIONING
AND
R
emove Styrofoam
packing
blocks and
corrugated
motor
block
packing
after
A NC H 0 RI N G
dishwasher
is removed
from
skid.
Re-
DISHWASHER
move
protector
panel
before
front
panels are installed.
Check
the upper
DOOR
SPRING
BRACKET
FIG.
7
rear portion
of the cabinet
opening
to make certain
that area is
cleared
of cabinet
or top
support
framing
members.
Set the
dishwasher
adjacent
to cabinet and adjust the four leveling
feet to
the desired height.
The four
leveling feet can be used to raise the
dishwasher
to 36"
or lower
to X3-11/16"
(33-7/16"
if leveling
screws are removed).
Adjust kickplate.
Kickplate
can be adjusted by
moving up or down.
After
the dishwasher
is in position,
make sure it is level from side to
side and front
to
rear.
If possible
dishwasher
front
should
be
parallel
to
counter
top
and flush
with
cabinets.
To maintain
alignment
of dishwasher
with adjacent
cabinets,
fasten dishwasher
to counter
top with two #lO flat head wood screws (not furnished).
Use these
screws
in
the
two
L
shaped
adjustable
brackets
(furnished)
at the
upper
left
and
right
hand
corners
of
T
,
dishwasher,
When dishwasher
is not installed
beneath a continuou,.
counter
top it may be necessary to anchor dishwasher
to floor using
l/4"
lag bolt or screw, in hole provided.
If door tension adjustment
is required,
adjust door spring so the door is counterbalanced
and
will remain in open position.
Adjust tension
by changing bracket to
alternate
holes and/or moving spring hooks to alternate
position.