Decora 16293 Manuel

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Decora 16293. Decora 16293 3 pages. Universal switch

Imprimer la page

ecora

Leviton Residential Powerline Carrier Components are designed to provide the greatest signal integrity and noise

ome

immunity possible. However, in some environments intense electrical noise can cause interference with the signal.

ontrols

Leviton has developed hardware and techniques for overcoming this interference when properly applied.

LEVITON'S DHC DEVICES FEATURE INTELLISENSE, THE RIGHT TYPE OF AUTOMATIC GAIN CONTROL (AGC)

Leviton DHC devices use Intellisense, a special gated-type of AGC, to help eliminate noise problems. This circuit feature

Universal Switch

is ideal for powerline carrier systems because it only operates during the signal window when receivers listen for

(Single Pole or 3 Way)

command signals. Noise levels in the signal window are never as high as they are during other portions of the AC power

curve. Therefore, Leviton's Intellisense gated AGC will

desensitize a receiver to noise signals with only a minimal

Rated:

10A-120VAC, 60HZ

reduction in command signal sensitivity. The result: Problems

from noise interference are dramatically reduced without

Cat. No. 16293

affecting overall system performance.

It is the responsibility of the specifier/installer to test for signal

Incandescent: 1200W max.,

strength and the presence of noise using Leviton test

60W min. – 10A, 120VAC

equipment, Cat. Nos. 6385 (Signal Test Transmitter) and 6386

(Signal Strength Indicator), and to properly apply signal

Fluorescent: 1200VA max.,

coupling and noise reduction equipment according to the

guidelines provided in the Decora Home Controls (DHC)

60VA min. – 10A, 120VAC

Technical Manual and the DHC Troubleshooting Guide.

Magnetic: 1200VA max.,

Leviton specifically denies any warranty of performance, stated or implied, where electrical noise interference exists at

60VA min. – 10A, 120VAC

the time of installation, or subsequent to installation by the addition of noise-producing devices or equipment, or where

these components have been installed for non-residential applications.

Supplemental: 1/4hp – 5.8A, 120VAC

DHC Components are for residential use only. Installation for any other application voids any warranty, stated or implied.

INSTALLATION INSTRUCTIONS

The Leviton Universal Switch, Cat. No. 16293, is designed for use with DHC Residential Powerline Carrier

Components. Cat. No. 16293 functions as a remote switching device which responds to coded ON/OFF, and ALL

LIGHTS ON/OFF commands.

Cat. No. 16293 can be operated manually as a standard type switch. The switch may be set to any of 256 address codes,

to be selected at the time of installation. The desired address is set by removing the switch plate and selecting letter and

DI-000-16293-00D

number codes with the tool provided. The module is equipped with six-inch leads and installs in a standard wall box. It is

suitable for incandescent, fluorescent, and magnetic low-voltage lighting loads.

LIMITED 2 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not

THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS B DIGITAL

for the benefit of anyone else that this product at the time of its

DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE

sale by Leviton is free of defects in materials and workmanship

PROTECTION AGAINST HARMFUL INTERFERENCE IN A RESIDENTIAL INSTALLATION. THIS EQUIPMENT

under normal and proper use for two years from the purchase

date. Leviton's only obligation is to correct such defects by repair

GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN

or replacement, at its option, if within such two year period the

ACCORDANCE WITH THE INSTRUCTIONS, MAY CAUSE HARMFUL INTERFERENCE TO RADIO

product is returned prepaid, with proof of purchase date, and a

COMMUNICATIONS. HOWEVER, THERE IS NO GUARANTEE THAT INTERFERENCE WILL NOT OCCUR IN A

description of the problem to Leviton Manufacturing Co., Inc.,

PARTICULAR INSTALLATION. IF THIS EQUIPMENT DOES CAUSE HARMFUL INTERFERENCE TO RADIO OR

Att: Quality Assurance Department, 59-25 Little Neck

TELEVISION RECEPTION, WHICH CAN BE DETERMINED BY TURNING THE EQUIPMENT OFF AND ON, THE USER

Parkway, Little Neck, New York 11362-2591. This warranty

IS ENCOURAGED TO TRY TO CORRECT THE INTERFERENCE BY ONE OR MORE OF THE FOLLOWING MEASURES:

excludes and there is disclaimed liability for labor for removal of

this product or reinstallation. This warranty is void if this product

• REORIENT OR RELOCATE THE RECEIVING ANTENNA.

is installed improperly or in an improper environment,

overloaded, misused, opened, abused, or altered in any manner,

• INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER.

or is not used under normal operating conditions or not in

• CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT TO WHICH THE

accordance with any labels or instructions. There are no other

RECEIVER IS CONNECTED.

or implied warranties of any kind, including merchantability and

fitness for a particular purpose, but if any implied warranty is

• CONSULT THE DEALER OR AN EXPERIENCED RADIO/TV TECHNICIAN FOR HELP.

required by the applicable jurisdiction, the duration of any such

implied warranty, including merchantability and fitness for a

particular purpose, is limited to two years. Leviton is not liable

for incidental, indirect, special, or consequential damages,

WARNING:

including without limitation, damage to, or loss of use of, any

equipment, lost sales or profits or delay or failure to perform

REGULATIONS.

this warranty obligation. The remedies provided herein are the

WARNING:

exclusive remedies under this warranty, whether based on

ELECTRICIAN.

contract, tort or otherwise.

WARNING:

For Technical Assistance Call:

INSTALL TO CONTROL A RECEPTACLE, MOTOR-OPERATED APPLIANCE, FLUORESCENT LIGHTING FIXTURE, OR

1-800-824-3005 (U.S.A. Only)

A TRANSFORMER-SUPPLIED APPLIANCE.

www.leviton.com

CAUTION

1. USE WITH MAGNETIC LOW-VOLTAGE TRANSFORMERS, INCANDESCENT, OR 120V HALOGEN FIXTURES

ONLY. USE A LEVITON ELECTRONIC LOW-VOLTAGE DIMMER TO CONTROL ELECTRONIC (SOLID STATE) LOW-

VOLTAGE TRANSFORMERS.

DI-000-16293-00D

INTRODUCTION

Signal Window

Command Signal

is picked up

DESCRIPTION

FCC COMPLIANCE STATEMENT

INSTALLATION INSTRUCTIONS

TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND

IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED

TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE TO OTHER EQUIPMENT, DO NOT

(For Incandescent Only): USE WITH INCANDESCENT OR 120V HALOGEN FIXTURES ONLY.

(For Magnetic Low-Voltage Only):

2. WHEN A MAGNETIC LOW-VOLTAGE CIRCUIT IS OPERATED AT A DIM LEVEL, WITH ALL LAMPS INOPERATIVE,

EXCESS CURRENT MAY FLOW THROUGH THE TRANSFORMER. TO AVOID POSSIBLE TRANSFORMER FAILURE DUE

TO OVERCURRENT, USE A TRANSFORMER THAT INCORPORATES THERMAL PROTECTION OR A FUSE AT THE

PRIMARY WINDINGS..

OTHER CAUTIONS AND NOTES:

1. DISCONNECT POWER WHEN SERVICING FIXTURE OR CHANGING BULBS.

2. USE THIS DEVICE ONLY WITH COPPER OR COPPER CLAD WIRE. WITH ALUMINUM WIRE USE ONLY

DEVICES MARKED CO/ALR OR CU/AL.

3. SAVE THIS INSTRUCTION SHEET. IT CONTAINS IMPORTANT TECHNICAL DATA ALONG WITH TESTING AND

TROUBLESHOOTING INFORMATION WHICH WILL BE USEFUL AFTER INSTALLATION IS COMPLETE.

Signal Window

Receiver sensitivity

TO INSTALL:

with Intellisense

gated AGC

WARNING:

TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND

TEST THAT POWER IS OFF BEFORE WIRING!

2. Remove existing wallplate and switch or dimmer, if applicable.

3. Remove 3/4" (1.9 cm) of insulation from each circuit conductor. Make sure that ends of conductors are straight.

Gated AGC ignores

Noise is not

4. Connect lead wires per appropriate WIRING DIAGRAM as follows: Twist strands of each lead tightly and, with circuit

High noise levels

picked up

conductors, push firmly into appropriate wire connector. Screw connectors on clockwise making sure that no bare

outside signal window

conductor shows below the wire connectors. Secure each connector with electrical tape.

NOTE: For single pole applications, cap YELLOW lead with an appropriate size wire connector. Secure connector

with electrical tape.

5. Using a small blade screwdriver, remove the switch plate by gently prying it off (refer to Figure 1).

6. Using the tool provided, set the House Code Dial Letter and the Unit Code Dial Number to the desired code

(refer to Figure 2).

7. If it is desirable to change the color of the device, do so now by following the " Color Conversion Procedure".

8. Mount device "TOP" up to wall box.

9. Restore power at circuit breaker or fuse. INSTALLATION IS COMPLETE.

The color of Cat. Nos. 16293 can be changed to suit your interior design requirements. Simply obtain a color conversion

kit of the appropriate color from your Leviton distributor or use the one provided, and proceed as follows:

1. The switch plate has snaps on its sides. Place the tip of a small-bladed screwdriver under a snap and gently pry off

the switch plate (refer to Figure 1).

2. Take the new switch plate and position it properly to the strap. Notice that the switch plate has an A/C indicator light at

one end. The switch plate should be installed with the A/C indicator light positioned at the bottom. With the switch plate

properly positioned, gently press it into place until it seats properly with a click. The color conversion is complete.

Figure 1 – Switch Plate Removal

Switch Plate

Strap

Push in 2 Locations

(see arrows)

2/7/01, 3:55 PM

COLOR CONVERSION PROCEDURE

Figure 2 – Dimmer Functions

Adjustment Tool

AC Indicator

Light

Unit Code Dial

House Code Dial