Berner ALC08 Series Manuel d'installation et d'entretien - Page 14

Parcourez en ligne ou téléchargez le pdf Manuel d'installation et d'entretien pour {nom_de_la_catégorie} Berner ALC08 Series. Berner ALC08 Series 16 pages.

Imprimer la page
Berner ALC08 Series Manuel d'installation et d'entretien
SYMPTOMS
NO AIR
MINIMUM AIR
AIR IS NOT HITTING
FLOOR
UNEVEN AIR
EXCESSIVE AIR
MOVEMENT AT DOOR-
WAY
NO HEAT
MINIMAL HEAT
EXCESSIVE HEAT
EXCESSIVE HEAT
MINIMAL HEAT
X. TROUBLESHOOTING
CAUSE
•
Power supply line open (no power)
•
Fuse blown/circuit breaker tripped
•
Motor overload tripped
•
Failed switch
MOTOR RUNNING/FANS ARE NOT ROTATING
• Broken or damaged flexible hub
•
Shaft rotating inside fan
ELECTRICAL CONTROLS NOT FUNCTIONING WHEN DOOR IS OPEN
•
Selector switch is in off position
•
Door limit switch not operating
•
Air directional discharge vanes mis-adjusted
•
Inadequate intake clearance
•
Blower motor operates below speed
•
Fan rubbing against housing
•
Fan wheels clogged with dirt
•
Fan in backwards
•
Air stream too weak
•
Air steam hits obstruction
•
Negative pressure
•
Shaft rotating inside fan
•
One motor not operating
•
Nozzle not angled out far enough
•
Unit too powerful
•
Air movement too cold
•
Pushing air outside building
SEE AIR IS NOT HITTING FLOOR SYMPTOMS
ELECTRICALLY HEATED MODELS
•
Switch turned to "ON" position
•
Thermostat not set properly
•
Coils burned out due to lack of air
•
Automatic reset thermal cutout failed in open position
•
Manual reset thermal cutout tripped (if supplied)
•
Thermostat in wrong location - thermostat too
close to discharge
•
Improper voltage
•
Thermostat not set properly
•
Low entering air temperature
•
Incorrect speed range
•
Thermostat in wrong location
•
Thermostat not set properly
• Insufficient air over coil
•
Improper voltage
STEAM/HOT WATER HEATED UNITS
•
Too high steam/hot water pressure
• Inadequate air flow, fins plugged up, dirty coils
• Insufficient removal of condensation (steam)
•
Not enough steam pressure/water temperature too
low
•
Intake air below design temperature
•
Check power source, check method of control in ON
position
•
Replace fuse(s)/reset breaker
•
Internally protected motor - should reset automatically
after cool-down, if not, replace motor.
•
Replace switch
•
Replace fan sleeve/reengage coupling
•
Tighten set screws/tighten fan on shaft
•
Turn switch to "ON" position
•
Repair or replace limit switch
•
Adjust vanes to proper position, see instructions
•
Move air curtain or remove obstruction
•
Provide adequate space for air curtain
•
Improper voltage
•
Free fan from housing
•
Clean and vacuum fan wheels
•
Check fans for blade curve toward discharge
•
Adjust nozzle to proper position, adjust motor speed;
see installation instructions
•
Remove obstruction or reposition air curtain (move out
3/8" for every 1" up from the door)
•
Relieve negative pressure by providing makeup air
•
Tighten set screws
•
Repair or replace motor
•
Adjust nozzle angle to outside
•
Adjust motor speed
•
Add auxiliary heat to overcome wind chill factor
•
Adjust discharge angle back into building, adjust motor
speed
•
Replace switch or check wiring
•
Change thermostat setting
• Correct airflow problem; replace coils
•
Replace automatic thermal cutout
•
Reset manual thermal cutout
•
Move thermostat away from air stream
•
Supply proper voltage
•
Change temperature setting
•
Based on unit temperature rise, reduce speed
•
Set dip switch to electric heated speed range
•
Move the thermostat closer to air stream
•
Change temperature setting
•
Remove restriction on intake
•
Supply proper voltage
• Reduce steam pressure/hot water flow
•
Clean intake and coils
•
Increase trap size
• Raise pressure for steam/increase water flow
• Increase steam pressure/increase water flow
19
REMEDY