Briteq BT-60ls Manuel - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Briteq BT-60ls. Briteq BT-60ls 8 pages. 60watt led moving head

Imprimer la page

ENGLISH

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper

installation can result in serious injuries and/or damage to property. Overhead rigging requires

extensive experience! Working load limits should be respected, certified installation materials

should be used, the installed device should be inspected regularly for safety.

 Make sure the area below the installation place is free from

unwanted persons during rigging, de-rigging and servicing.

 Locate the fixture in a well ventilated spot, far away from

any flammable materials and/or liquids. The fixture must

be fixed at least 50cm from surrounding walls.

 The device should be installed out of reach of people and

outside areas where persons may walk by or be seated.

 Before rigging make sure that the installation area can hold

a minimum point load of 10times the device's weight.

 Always use a certified safety cable (number 3 on the

picture) that can hold 12 times the weight of the device

when installing the unit. This secondary safety attachment

should be installed in a way that no part of the installation

can drop more than 20cm if the main attachment fails.

 The device should be well fixed; a free-swinging mounting

is dangerous and may not be considered!

 Don't cover any ventilation openings as this may result in overheating.

 The operator has to make sure that the safety-relating and machine-technical

installations are approved by an expert before using them for the first time. The

installations should be inspected every year by a skilled person to be sure that

safety is still optimal.

1. Optional Clamp

2. Special omega clamp (included)

3. Threaded hole, used to install the supplied eyebolt

4. Optional safety cable

HOW TO SET UP THE UNIT

CONTROL PANEL:

1. DISPLAY shows the various menus and the selected functions.

2. LEDS

DMX

MASTER

SLAVE

SOUND

Flashing

JB SYSTEM

OPERATION MANUAL

DMX input present

Master mode

Slave mode

Sound activation

3/11

BT-60LS

ENGLISH

3. BUTTONS

To select the programming functions

DOWN

To go backward in the selected functions

To go forward in the selected functions

ENTER

To confirm the selected functions

4. DMX INPUT/OUTPUT: used for DMX512 linking. Use good quality 3pin XLR M/F balanced cable to link

the units together.

5. WIRED REMOTE CONTROL INPUT: Used to connect a simple CA-8 hand controller while the unit is

used in standalone or master/slave mode.

6. WIRELESS REMOTE CONTROL INPUT: Used to connect RF-8 wireless controller while the unit is used

in standalone or master/slave mode.

7. MAINS INPUT: with IEC socket and integrated fuse holder, connect the supplied mains cable here.

MAIN MENU:

 To select any of the functions, press the MENU button

up to when the required one is shown on the display

or use the DOWN and UP buttons to browse the

menu.

 Select the function with the ENTER button (the display

blinks).

 Use DOWN and UP buttons to change the mode.

 Once the required mode is selected, press the

ENTER button to confirm. To go back to the main

menu without any change press the MENU button

shortly. The main menu is shown in the chart.

DMX Address

Used to set the starting address in a DMX setup.

 Press the MENU button until "DMX Address" is shown

on the display.

 Press the ENTER button, the display starts blinking.

 Use DOWN and UP buttons to change the DMX512

address.

 Once the correct address shows on the display, press

the ENTER button to save it.

To go back to the main menu without any change press

the MENU button shortly.

If you want to go back to normal running mode: press

the MENU button for about 2 seconds.

Channel mode

Used to set the desired channel setup mode.

 Press the MENU button until "Channel mode" is

shown on the display.

 Press the ENTER button, the display starts blinking.

 Use DOWN and UP buttons to choose 1MSL, 4MSL

or 15Chan mode.

 Once the desired channel setup mode shows on the

display, press the ENTER button to save it.