IKEA tradfri Manuel de démarrage rapide - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} IKEA tradfri. IKEA tradfri 12 pages. Motion sensor
Également pour IKEA tradfri : Manuel de l'utilisateur (36 pages), Manuel d'instructions de montage (36 pages), Manuel d'instructions de montage (24 pages), Manuel (12 pages), Manuel (28 pages), Manuel (20 pages), Manuel (16 pages), Manuel (20 pages), Manuel rapide (36 pages), Manuel (16 pages), Manuel (32 pages), Manuel (12 pages), Manuel (8 pages), Manuel (24 pages), Manuel (24 pages), Manuel (32 pages), Manuel (24 pages), Manuel (32 pages), Manuel (32 pages), Manuel (24 pages), Manuel (12 pages), Manuel (24 pages), Manuel (24 pages), Manuel (24 pages), Manuel (29 pages), Manuel (12 pages), Manuel (40 pages), Manuel de démarrage rapide (24 pages), Manuel de démarrage rapide (16 pages), Manuel (16 pages), Manuel (24 pages), Manuel (32 pages), Manuel de démarrage rapide (2 pages), Manuel (40 pages), Manuel de démarrage rapide (16 pages), Manuel (36 pages), Manuel (28 pages), Manuel de démarrage rapide (2 pages), Manuel (32 pages), Manuel (32 pages), Manuel (24 pages), Manuel d'instructions (8 pages), Manuel (24 pages), Manuel de démarrage rapide (4 pages), Manuel (8 pages), Manuel (20 pages), Manuel (12 pages), Manuel (8 pages), Manuel (32 pages)

Imprimer la page

English

HOW TO STEER YOUR LIGHTING

The switch on your power supply cord

will make it possible to turn ON/OFF

all products connected to the TRÅDFRI

driver, but if you want to dim or connect

your products to IKEA Smart lighting

products, you need to buy a separate

TRÅDFRI steering device (e.g. a remote

control).

The TRÅDFRI steering device needs to

be paired with your TRÅDFRI driver/s.

If you have more than one (1) driver

you can pair each one with the steering

device, so that the entire combination

can be turned ON/OFF or dimmed at the

same time.

Depending on how easy it will be to

access the driver please consider to pair

the TRÅDFRI driver/s with your steering

device before the final placement of the

driver/s and cords.

PAIRING A STEERING DEVICE

TO YOUR DRIVER

1. Connect at least one (1) product to the

driver before you begin the pairing.

Make sure that the power supply

cord is connected to a power socket

and that the switch on the cord set is

turned ON.

2. Locate the pairing symbol

driver. Hold the steering device close

to the pairing symbol (no more than 5

cm away).

3. Press and hold the pairing button

on the steering device for at least 10

seconds. A red light will shine steadily

on the steering device.

The product connected to the driver

will begin to dim and flash one time

to indicate that the driver is being

paired to the steering device.

HOW TO FACTORY RESET YOUR DRIVER

If the driver does not respond or if

you want to un-pair the driver from

a steering device you might have to

make a factory reset. The driver is

forced to factory reset by carefully

inserting a paper clip end or similar in

the small hole (marked RESET) in the

driver enclosure and applying a slight

pressure.

IMPORTANT!

• The driver is for indoor use only and

can be used in temperatures ranging

from 5ºC to 45 ºC (41ºF to 113 ºF).

• Do not leave the driver in direct

sunlight or near any heat source, as it

may overheat.

• Do not subject the driver to wet, moist

or excessively dusty environments as

this may cause damage.

• The declared radio range between

the driver and the steering device

is measured in open air. Different

building materials and placement

of the units can affect the wireless

connectivity range.

CARE INSTRUCTIONS

To clean the driver, wipe with a dry soft

cloth.

on the

Never use abrasive cleaners or chemical

solvents as this can damage the

product.

PRODUCT SERVICING

Do not attempt to repair this product

yourself, as opening or removing covers

may expose you to dangerous voltage

points or other risks.