IKEA tradfri Manuel - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} IKEA tradfri. IKEA tradfri 24 pages. Motion sensor
Également pour IKEA tradfri : Manuel de l'utilisateur (36 pages), Manuel d'instructions de montage (36 pages), Manuel d'instructions de montage (24 pages), Manuel (12 pages), Manuel (28 pages), Manuel (20 pages), Manuel (16 pages), Manuel (20 pages), Manuel rapide (36 pages), Manuel (16 pages), Manuel (32 pages), Manuel (12 pages), Manuel (8 pages), Manuel (24 pages), Manuel (24 pages), Manuel (32 pages), Manuel (24 pages), Manuel (32 pages), Manuel (32 pages), Manuel (24 pages), Manuel (12 pages), Manuel (24 pages), Manuel (24 pages), Manuel (24 pages), Manuel (29 pages), Manuel (12 pages), Manuel de démarrage rapide (12 pages), Manuel (40 pages), Manuel de démarrage rapide (24 pages), Manuel de démarrage rapide (16 pages), Manuel (16 pages), Manuel (24 pages), Manuel (32 pages), Manuel de démarrage rapide (2 pages), Manuel (40 pages), Manuel de démarrage rapide (16 pages), Manuel (36 pages), Manuel (28 pages), Manuel de démarrage rapide (2 pages), Manuel (32 pages), Manuel (32 pages), Manuel (24 pages), Manuel d'instructions (8 pages), Manuel de démarrage rapide (4 pages), Manuel (8 pages), Manuel (20 pages), Manuel (12 pages), Manuel (8 pages), Manuel (32 pages)

Imprimer la page

ENGLISH

FUNCTIONS MOTION SENSOR

Adjust the time setting. The lights will turn off

either 1, 5 or 10 minutes after the last motion is

detected.

Day/Night setting. During the daytime the lights

will always turn on when triggered by motion. At

night the lights will only turn on when it is dark

and they are triggered by motion.

Button for pairing. Add IKEA Smart lighting products

to your system. Follow the instructions below:

ADDING DEVICES TO YOUR MOTION SENSOR

Your kits come already paired, so you will not need to

pair them yourself.

Before you can use your motion sensor it must be paired

to the light source you want to steer. If you want to add

more light sources, just repeat the steps below for each

individual light source.

1 Make sure that your light source is installed and the

power is turned on.

2 Hold the motion sensor close to the light source you

want to add (no more than 5 cm away).

3 Press and hold the pairing button

seconds. A red LED light will shine steadily on the front

side of the motion sensor.

4 Your light source will flash one time to indicate that it

has successfully paired.

Up to 10 light sources can be paired with 1 motion

sensor.

Make sure to pair them one at a time. If the light sources

are close to each other, disconnect those that have

already been paired from the main power switch.

REMOVING DEVICES FROM YOUR MOTION SENSOR

1 Make sure the device you want to remove from your

2 Hold the motion sensor close to the light source you

3 Press and hold the pairing button

4 Your light source will flash twice to indicate that it has

FACTORY RESET

Lighting products:

Toggle the main power switch 6 times.

Motion sensor:

Press the pairing button

CHANGE BATTERY:

When unit is used regularly and as intended, the

batteries will last for approximately 2 years.

for at least 10

A red LED indicator will shine steadily when it's time to

replace the batteries.

Open the battery lid and replace the batteries with

CR2032 type batteries.

TRÅDFRI motion sensor is turned on.

want to remove (no more than 5 cm away).

seconds. A red LED light will shine steadily on the front

side of the motion sensor.

successfully un-paired.

for at least 10

4 times within 5 seconds.