Makita 3708FC Manuel d'instruction - Page 7
Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Makita 3708FC. Makita 3708FC 12 pages. Trimmer
Également pour Makita 3708FC : Spécifications (2 pages), Liste des pièces (3 pages), Ventilation des pièces (3 pages), Manuel d'instruction (16 pages)
Imprimer la page
ENGLISH
1
Loosen
2
Tighten
3
Hold
4
Wing nut
5
Spring washer
6
Flat washer (small)
7
Base
8
Flat washer (large)
9
Bolt
10 Trimmer shoe
11 Adjusting roller
12 Scale
13 Bit protrusion
14 Lever
15 Graduation
16 Wing bolt
17 Amount of chamfering
18 Switch lever
19 Workpiece
20 Feed direction
SPECIFICATIONS
Model
Collet capacity .............................................6 mm or 1/4"
–1
No load speed (min
) .......................................... 35,000
Overall length ..................................................... 308 mm
Net weight .............................................................. 1.3 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
Explanation of general view
21 Bit revolving direction
22 (View from the top of
the tool)
23 Correct bit feed direction
24 Trimmer shoe, straight guide
or trimmer guide
25 Bolt
26 Guide plate
27 Straight guide
28 Flat washer
29 Wave washer
30 Wing nut
31 Clamp screw (A)
32 Centre hole
33 Nail
34 Adjusting screw
35 Clamp screw (B)
36 Trimmer guide
37 Bit
38 Guide roller
ADDITIONAL SAFETY RULES
3708/3708F
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Be careful of the bit rotating direction and the
11. Do not leave the tool running. Operate the tool
12. Always switch off and wait for the bit to come to
13. Do not touch the bit immediately after operation;
14. Always lead the power supply cord away from
15. Do not smear the tool base carelessly with thin-
16. Draw attention to the need to use cutters of the
SAVE THESE INSTRUCTIONS.
39 Screws
40 Screwdriver
41 Templet guide
42 Convex portions
43 Straight bit
44 Templet
45 Distance (X)
46 Not available
47 Not available
48 Not available
49 Not available
50 Not available
51 Not available
52 Not available
53 Not available
54 Not available
55 Limit mark
56 Brush holder cap
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
Wear hearing protection during extended peri-
ods of operation.
Handle the bits very carefully.
Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly.
Keep hands away from rotating parts.
Make sure the bit is not contacting the work-
piece before the switch is turned on.
Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
feed direction.
only when hand-held.
a complete stop before removing the tool from
workpiece.
it may be extremely hot and could burn your skin.
the tool towards the rear.
ner, gasoline, oil or the like. They may cause
cracks in the tool base.
correct shank diameter and suitable for the
speed of the tool.
ENB054-1
7