Makita 4100NH2 Manuel d'instruction - Page 5

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Makita 4100NH2. Makita 4100NH2 8 pages.
Également pour Makita 4100NH2 : Manuel d'instruction (12 pages)

Imprimer la page

c) Do not position your body in line with the

rotating wheel. Kickback will propel the tool in

direction opposite to the wheel's movement at the

point of snagging.

d) Use special care when working corners,

sharp edges etc. Avoid bouncing and snagging

the accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain, woodcarving

blade, segmented diamond wheel with a

peripheral gap greater than 10 mm or toothed

saw blade. Such blades create frequent kickback

and loss of control.

f) Do not "jam" the wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases

the loading and susceptibility to twisting or binding

of the wheel in the cut and the possibility of

kickback or wheel breakage.

g) When wheel is binding or when interrupting

a cut for any reason, switch off the power tool

and hold the power tool motionless until the

wheel comes to a complete stop. Never

attempt to remove the wheel from the cut while

the wheel is in motion otherwise kickback may

occur. Investigate and take corrective action to

eliminate the cause of wheel binding.

h) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted in

the workpiece.

i) Support panels or any oversized workpiece

to minimize the risk of wheel pinching and

kickback. Large workpieces tend to sag under

their own weight. Supports must be placed under

the workpiece near the line of cut and near the

edge of the workpiece on both sides of the wheel.

j) Use extra caution when making a "pocket

cut" into existing walls or other blind areas.

The protruding wheel may cut gas or water pipes,

electrical wiring or objects that can cause kickback.

18. Before using a segmented diamond wheel,

make sure that the diamond wheel has the

peripheral gap between segments of 10 mm or

less, only with a negative rake angle.

Additional Safety Warnings:

19. Never attempt to cut with the tool held upside

down in a vise. This can lead to serious

accidents, because it is extremely dangerous.

20. Some material contains chemicals which may

be toxic. Take caution to prevent dust

inhalation and skin contact. Follow material

supplier safety data.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence

to safety rules for the subject product. MISUSE or

failure to follow the safety rules stated in this

instruction manual may cause serious personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

Always be sure that the tool is switched off and

•

unplugged before adjusting or checking function

on the tool.

Adjusting the depth of cut

009555

Loosen the clamping nut on the depth guide and move

the base up or down. At the desired depth of cut, secure

the base by tightening the clamping nut.

CAUTION:

After adjusting the depth of cut, always tighten the

•

clamping nut securely.

Adjusting bevel angle

009567

Loosen the clamping nut on the bevel scale plate on the

front of the base. Set for the desired angle (0 - 45

degrees) by tilting accordingly, then tighten the clamping

nut with your hand securely.

Loosen the clamping nut on the depth guide and move

the base up or down. At the desired depth of cut, secure

the base by tightening the clamping nut.

1. Base

2. Clamping nut

1. Clamping nut