Makita 6706D Manuel d'instruction - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Makita 6706D. Makita 6706D 14 pages. Cordless angle socket driver
Également pour Makita 6706D : Liste des pièces (2 pages), Manuel d'instruction (8 pages), Manuel d'instruction (8 pages)

Imprimer la page

Do not touch the bit or the workpiece immedi-

ately after operation; they may be extremely hot

and could burn your skin.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious per-

sonal injury.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 1)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, pull out the set plate

on the tool and grasp both sides of the cartridge while

withdrawing it from the tool.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Snap the set plate back into place. Be sure

to close the set plate fully before using the tool.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Installing or removing socket

Important:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before installing or removing

the socket.

For tool with square drive (Fig. 2 & 3)

Use 9.5 mm square drive socket with a hole for detent pin

which is available on the market. (Note: Use 6.35 mm

square drive socket when using the tool with 6.35 mm

square drive.)

To install the socket, depress the detent pin on the

square drive with your finger and push the socket onto

the square drive until the detent pin is inserted into the

hole in the socket.

To remove the socket, depress the detent pin with a

small hand tool and pull off the socket.

For tool with round drive (Fig. 4)

Use a bit with Form C 6.3 shank which is available on the

market. The bit can be inserted directly into the round

drive and held in place.

To install the bit, push it firmly into the round drive.

To remove the bit, grasp it with a pair of pliers and pull it

out of the round drive. Sometimes, it helps to wiggle the

bit with the pliers as you pull.

Switch action (Fig. 5)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the "OFF" position when released.

To start the tool, simply pull the trigger. Release the trig-

ger to stop.

Reversing switch action (Fig. 5)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

This tool has a reversing switch to change the direction

of rotation. Slide the reversing switch up for clockwise

rotation or slide it down for counterclockwise rotation.

Overload protector

For 6704D

The overload protector automatically cuts out to break

the circuit whenever heavy work is prolonged. Wait 20 –

30 seconds before resuming operation.

Adjusting the fastening torque (Fig. 6)

The fastening torque can be adjusted infinitely from

approx. 20 kg cm to 80 kg cm. To adjust it, loosen the two

screws and turn the adjusting ring. Then tighten the

screws to secure the adjusting ring. Refer to the table

below for relation between the numbers on the adjusting

ring and the fastening torque to be obtained.

Numbers on

adjusting ring

(Example)

35 kg cm of fastening torque can be obtained when the

number 2 is aligned to the red mark.

NOTE:

• Always tighten the two screws to secure the adjusting

ring after adjusting the fastening torque.

• The fastening torque may differ depending upon the

kind of screws, the type of materials to be fastened,

etc. Before starting your job, always perform a test

operation to verify the adequate fastening torque.

Installing set plate (Fig. 7)

Always install the set plate when using battery cartridges

9100, 9102 or 9102A. Install the set plate on the machine

with the screw provided as shown in Fig. 7.

Operation

The proper fastening torque may differ depending upon

the kind or size of screws, the type of materials to be fas-

tened, the condition of the threads, etc. Before starting

your job, always perform a test operation to verify ade-

quate fastening torque.

Hold the tool firmly with both hands whenever possible

and place the socket over the bolt or nut. Then turn the

tool on. As soon as the bolt or nut becomes tight, the

clutch will cut in and the motor will stop automatically.

Release the switch trigger.

When fastening tool screws, use the proper screwdriver

bit shown in Fig. 8. It is commonly available on the mar-

ket.

Fastening torque

to be obtained

20 kg cm

35 kg cm

48 kg cm

60 kg cm

80 kg cm