Avantgarde SPACEHORN Manuel de l'utilisateur - Page 9
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Avantgarde SPACEHORN. Avantgarde SPACEHORN 18 pages.
Imprimer la page
CONNECTION – TRIO G3 ITRON VERSION
BALANCED XLR CONNECTION
1 8
1 3
SPEAKER TYPE
TRIO G3
PUSH
MODEL NO.
ITRON AMP–TRIO
ORIGIN
MADE IN GERMANY
OUT
IN
FUSE
TRIGGER
SENSOR
12V DC
ON/OFF
ENGAGED
FUSE
E FUSE
DIMMER
POWER ON
POWER
RESET
TOGGLE
FOR HOME OR OFFICE USE
1 4
Line level connections feature balanced XLR connectors/terminals.
PUSH
The pin assignment of these follows the EIA RS-297-A standard:
2
1
PIN 1 = GND, PIN 2 = HOT, PIN 2 = COLD. Never use cables with
3
differing pin assignment! This will deteriorate the sound quality and
can damage the amplif iers and/or the active power modules of the
subwoofers.
1
Connect the line level output of your preamplif ier with the balanced
line level input
Connect the balanced XLR daisy chain output
2
speaker and the balanced XLR input of the SPACEHORNS with the
long XLR jumper cable. The jumper cable is included in the
accessory box.
3
If you use more than 1 x subwoofer per channel, connect the
balanced XLR daisy chain output of the SPACEHORNS No.1 and the
balanced XLR line level input of the SPACEHORNS No.2 with the
shorter XLR jumper cable. The jumper cable is included in the
accessory box.
4
Only now, connect the AC power
household AC outlet and turn on the ITRON module and the
subwoofer.
1 2
1 1
PUSH
INTERNAL CONNECT PORT
BALANCED SIGNAL
OUTPUT TO DRIVER
INPUT
OUTPUT
B C
+ 1.5
+ 1.5
+ 1.5
+ 1.5
+ 3
+ 6
A
D
0dB
– 1.5
– 1.5
– 1.5
– 1.5
– 3
– 6
LOW
MID
HIGH
TOTAL GAIN
MODE
DRIVER GAIN
SERIAL NO.
1 5
1 6
of the TRIO G3 speaker with an XLR cable.
of the TRIO G3
of the components to a
1
2
GND
3
B C
A
D
POWER ON
MODE
16
17
OPERATION – TRIO G3 ITRON VERSION
POWER MODES
The mains power switch
has an "O" OFF–position & an "1" ON–
position. For operation switch to the ON position.
The TRIO G3 features an illuminated sensor switch
side to turn the speaker ON.
ORANGE light = STANDBY
WHITE light
= ON
PURPLE light
= OTA f irmware update
The brightness of the light can be adjusted with the DIMMER
TOGGLE button
, toggling through 8 x intensities.
4 x different power ON/OFF modes can be selected with the POWER
ON mode selector
. Use a screwdriver to switch the modes.
newly selected modes will only become active after the mains
�
power switch
has been shortly switched OFF.
MODE A
speaker is ON upon powering it up with the mains
power switch
. To be used for remote controlled AC
power sockets. The f rontal sensor switch
be used to switch into standby mode, but upon next
power cycle the speaker will turn ON again directly.
MODE B
speaker is ON when a 12V trigger voltage is detected at
the
remote-trigger
socket
automatically switch OFF, when the 12V trigger voltage
is switched OFF.
MODE C
the f rontal sensor switch
speaker ON & STANDBY.
MODE D
speaker is switched ON & STANDBY by remote control
signal
(not available upon release; optional future upgrade only).
on its f ront
(optional future upgrade only)
1 7
may still
.
The
speaker
will
is used to toggle between