ALIBI ALI-NVR5316P Manuel d'installation rapide
Parcourez en ligne ou téléchargez le pdf Manuel d'installation rapide pour {nom_de_la_catégorie} ALIBI ALI-NVR5316P. ALIBI ALI-NVR5316P 8 pages. Embedded network video recorder
Imprimer la page
ALI-NVR5316P Embedded Network Video Recorder Quick Setup Guide
This quick setup guide provides instructions to initially setup and use the ALI-NVR5316P network video recorder (NVR). For additional
information on the extensive capabilities of your NVR, refer to the ALIBI™ Embedded Network Video Recorder Firmware V4.1.50 (or
later) User Manual. Additional documentation and software for this product can be found at AlibiSecurity.com/Resources.
NVR Front Panel
Item
Function / Description
POWER
Indicator is green when the unit is powered on. When the unit is off, the LED is red if power is available.
Status Indicators
HDD
HDD indicator blinks red when data is being read from or written to an HDD.
TX / RX
Blinks green when the network connection is functioning normally.
USB Interfaces
Universal Serial Bus (USB) ports for additional USB devices such as a mouse or Hard Disk Drive (HDD).
NVR Back Panel
eSATA
CVBS Video OUT
RS-232
Camera Channels
LAN
USB 3.0
(16, with POE)
Item
Description
RS-232 Interface
DB9 (male) connector for RS-232 devices
VIDEO OUT (VGA, HDMI1, 2)
See Specifications section
AUDIO IN / OUT
RCA connector for Line level audio input and output.
RS-485, ALARMS IN/OUT
See below.
POWER CONNECTOR
AC 100 V ~ 240 V power supply.
ON / OFF Switch
Switch for powering the device on or off.
GROUND
Terminal for ground. Connect to earth ground before powering on the NVR.
LAN Interface
10/100/1000BASE-T Ethernet network interface
USB interface
Universal Serial Bus (USB) 3.0 port for additional devices such as USB mouse and USB Hard Disk Drive (HDD).
Internal Ethernet switch ports
16 ports for IP cameras. These ports provide Power over Ethernet (PoE) to the cameras.
1
Status
indicators USB ports (2)
Monitor Out
(VGA, HDMI)
Alarm OUT
RS-485
Alarm IN 1..16
Ground
Fan outlet ON / OFF switch
Audio IN/OUT
RS-485, ALARMS IN/OUT
Item
RS-485 (D+, D-)
KB (D+, D-)
ALARM IN (1 through 16)
ALARM OUT
(1-G through 4-G)
Mouse Control
Power connector
A standard 3-button (left/right/scroll-wheel) USB mouse can also be used with this NVR. To use a USB mouse:
1.
Plug USB mouse into the either the front panel or backpanel USB connector of the NVR.
2.
The mouse will be automatically detected. If the mouse is not detected, the mouse may not be compatible with the NVR. Please refer
to the recommended device list from your provider.
The operation of the mouse:
Action
Effect
Live view: Show menu.
Right click
Menu: Exit current menu to upper level menu.
Single click: Live view: Select channel and show the quick set menu.
Menu: Select and enter.
Double click: Live view: Switch between single-screen and multi-screen.
Left click
Click and drag: PTZ control: pan, tilt and zoom.
Tamper-proof, privacy mask and motion detection: Select target area.
Digital zoom-in: Drag and select target area.
Live view: Drag channel/time bar
Scroll up: Live view: Previous screen.
Menu: Previous item.
Scroll wheel
Scroll down: Live view: Next screen.
Menu: Next item.
RS-485, Alarm IN / OUT terminations
Description
D+, D- half duplex terminations for RS-485 devices.
Controller port:
D+, D- pin connects to Ta, Tb pin of controller.
For cascading devices, the first NVR's D+, D- pin should be connected with the D+, D- pin of the next NVR
Alarm inputs 1 - 16. Alarm input is tied to ground through the alarm sensor.
Alarm outputs 1 - 4 with ground terminations.
ALI-NVR5332P_SQ
180919