E-T-A ESX10-TA -100 Manuel - Page 7
Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} E-T-A ESX10-TA -100. E-T-A ESX10-TA -100 15 pages. Electronic circuit protector
Imprimer la page
Electronic Circuit Protector ESX10-T.-DC 24 V - Installation guidelines and safety instructions
Dimensions ESX10-TA
83
3.27
80
3.15
Phoenix label ZBF 12
Dimensions ESX10-TB
83
3.27
80
3.15
Phoenix label ZBF 12
Dimensions ESX10-TD
83
3.27
80
3.15
Phoenix label ZBF 12
1822
12.5
.492
ok
r
e
on
s
o
e
t
2 LOAD+
snap-on socket for
symmetrical rail EN 50022-35x7.5
12.5
.492
snap-on socket for
symmetrical rail EN 50022-35x7.5
12.5
.492
switch for current
x A
x A
rating adjustment
xx A
ok
r
e
on
s
o
e
t
2 LOAD+
snap-on socket for
symmetrical rail EN 50022-35x7.5
www.e-t-a.de
Information on UL and CSA approvals
ESX10-TA/-TB/-TD
UL2367
Non-hazardous use - UL File # E306740
UL 508
Non-hazardous use
UL File # E322549
E322549
INDUSTRIAL CONTROL EQUIPMENT
ESX10-TA / -TB
ISA 12.12.01-2015
UL File # E320024
Operating Temperature Code T4
- This equipment is suitable for use in ClassⅠ, Division 2,
Groups A, B, C and D or non-hazardous locations only.
T4 A / 0°C to 50°C
Warning
- Exposure to some chemicals may degrade the sealing properties
of materials used in the following device: relay (K1)
• Sealant Material:
Generic Name: Modified diglycidyl ether of bisphenol A
Supplier:
Fine Polymers Corporation
Type:
Epi Fine 4616L-160PK
• Casing Material:
Generic Name: Liquid Crystal Polymer
Supplier:
Sumitomo Chemical
Type:
E4008, E4009, or E6008
RECOMMENDATION:
- Periodically inspect the device named above for any degradation
of properties and replace if degradation is found
WARNING – EXPLOSION HAZARD:
AVERTISSEMENT – RISQUE D'EXPLOSION
• Do not disconnect equipment unless power has been removed
or the area is known to be non-hazardous.
Avant de deconnecter l'equipment, couper le courant ou
s'assurer que l'emplacement est designe non dangereux.
• Substitution of any components may impair suitability for
Class I, Division 2.
La substitution de composants peut rendre ce materiel
inacceptable pour les emplacements de class I, division 2.
This device is OPEN type equipment that must be used within a suita-
ble end-use system enclosure, the interior of which is accessible only
through the use of a tool. The suitability of the enclosure is subject
to investigation by the local Authority Having Jurisdiction at the time
of installation.
Wiring to or from this device, which enters or leaves the system
enclosure, must utilize wiring methods suitable for Class I, Division 2
Hazardous Locations, as appropriate for the installation.
ESX10-TA / -TB
CSA C22.2 No: 14 - File # 016186
CSA C22.2 No: 142 - File # 016186
CSA C22.2 No: 213 (Class Ι, Division 2) - File # 016186
Class 2
Meets requirement for Class 2 current limitation
(ESX10-T...-0.5 A / 1 A / 2 A / 3 A)
4
7