Gardebruk MZ-KS110 Manuel - Page 11

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Gardebruk MZ-KS110. Gardebruk MZ-KS110 20 pages.

Imprimer la page

Fig 4

WARNING: ALWAYS UNPLUG THE UNIT BEFORE

CHANGING GRINDING WHEELS, OR WHEN

MAKING ANY ADJUSTMENTS TO THE SHARPEN-

ER.

Refer to the Assembly Drawing on page 11 and

FIGTURE 5 and FIGTURE 6 below.

1. Raise the Top Housing(#4) and lock it in the up

2. Remove the two screws holding the Grinding

Wheel Cover(#11). Set the cover aside.

3. Unscrew the screw and Grinder Lock Cap(#9)

that holds the Grinding Wheel(#8) in place.

4. Install the new wheel on the Grinding Wheel

Base(#7), making sure it ﬁts properly.

NOTE: DO NOT USE A GRINDING WHEEL IF IT IS

CHIPPED, CRACKED, OR WORN. YOU CAN CHECK

IF THE WHEEL HAS CRACK NOT VISIBLE TO THE

HUMAN EYE BY HANGING IT UP BY THE CENTRAL

HOLE AND TAPPING IT WITH A NON METAL

OBJECT(IE: SCREWDRIVER HANDLE). IF IT IS IN

GOOD CONDITION IT WILL PRODUCE A METALLIC

SOUND. A DULL SOUND INDICATES A CRACK OR

BREAK.

5. Replace the Grinder Lock Cap(#9).

www.DeubaXXL.de

6. Replace the Grinding Wheel Cover(#11).

7. Release the Lock Stop(#6) and lower the Top

Housing(#4).

8. Never operate tool without the Grinding Wheel

Cover in place.

FIG.5

FIG.6

IV.OPERATION

WARNING: ALWAYS UNPLUG THE UNIT WHILE

ADJUSTING CHAIN TO BE SHARPENED.

Refer to the Assembly Drawing on page 11 and

the various photographs.

NOTE: RAISE THE TOP HOUSING(#4) WHILE

ADJUSTING THE CHAIN.

1. Clean the chain before sharpening. Wash it

with a non-ﬂammable solvent. Do not use

gasoline. Dry the chain.

www.Deuba24online.de

chain in the Sliding Guides(#31). See FIGTURE 8.

3. Lower the Chain Stop(#23) so that it is

with. See FIGTURE 7

unterer Knopf

Abb. 7

V. Maintenance

1.Keep the Sharpener clean and free of dust,

metal debris and dirt.

blockage of dust, chips or workpiece fragments.

2. Check the Grinding Wheel before each use to

make sure it isn't damaged. Do not use a grinding

wheel if it is chipped, cracked, or worn. You can

check if the wheel has cracks not visible to the

human eye by hanging it up by the central hole

and tapping it with a non metal object(Ie:

will produce a metallic sound. A dull sound

indicates a crack or break.

3. Replace the Grinding Wheel when it grinds

down to a diameter of 3 inches.

Before Replace the Grinding Wheel , must

remove the guard in the right way . Please open

the guard without remove screws. Be careful and

stop screwing when you saw the screw thread

during unscrewing, or the screws will be dropped

www.Deuba24online.de

missing of the ﬁxing screws on the guard , please

guard have been removed. If you use electric/-

ful about it or you will easy to dismount the screw

Fig . 13

Winkelmesser

VI. ENVIRONMENT FRIENDLY DISPOSAL

ou can help protect the environment!

Please remember to respect the local

electrical equipment's to an appropri-

ate waste disposal centre .

VII. Maintenance and Care

Attention! When cleaning, always switch oﬀ the

saw chain sharpener and remove the mains

plug from the socket.

Clean your saw chain sharpener housing with a

slightly damp cloth. Then dry thoroughly.

Many detergents contain chemical substances

that can attack the plastic parts of the device.

Never use petrol, turpentine, thinner or similar

substances.

Store the saw chain sharpener in a dry room.

Always keep the saw blade sharpener air vents

clean. Protect the saw chain sharpener from

dust and dirt to avoid electric shock hazards. It

is normal for sparks to pop out of the air vents

from time to time.