ALIBI ALI-TS2128R Manuel d'installation rapide - Page 5

Parcourez en ligne ou téléchargez le pdf Manuel d'installation rapide pour {nom_de_la_catégorie} ALIBI ALI-TS2128R. ALIBI ALI-TS2128R 5 pages. 8mp tvi/ahd/cvi/cvbs varifocal 200 ft ir outdoor turret camera

Imprimer la page

DNR (Digital Noise Reduction): Use DNR function to decrease the noise in the image, especially when

capturing moving images in poor light conditions, to produce a sharper image. You can set the DNR value

from 1 to 9.

MIRROR: This feature is used to reflect the image. MIRROR can be set to OFF, H, V, and HV.

OFF: The mirror function is disabled.

H: The image flips 180° horizontally.

V: The image flips 180° vertically.

HV: The image flips 180° both horizontally and vertically.

FACTORY DEFAULT

Click Iris+ to enter the submenu, and click OK to reset all the settings to the factory default. Click Cancel

to return to the menu without resetting the camera.

EXIT

Move the cursor to EXIT and click Iris+ to exit the menu without saving.

SAVE & EXIT

Move the cursor to SAVE & EXIT, and click Iris+ to save the settings and exit the menu. If new settings are

not saved, they remain in effect only until the camera is powered off or reset.

Specifications

Camera

Image Sensor

8.29 MP progressive scan CMOS sensor

TVI: 8MP @ 12.5 fps, 8MP @ 15 fps, 5MP @ 20 fps, 4MP @ 25 fps, 4MP @ 30 fps, 2MP @ 25 fps,

2MP @ 30 fps

Frame Rate

CVI: 8MP @ 12.5 fps, 8MP @ 15 fps

AHD: 8M @ 12.5 fps, 8M @ 15 fps

CVBS: 960H P/N

Effective Pixels

3840 (H) × 2160 (V)

Min. illumination

Color: 0.01 Lux @ (F1.2, AGC ON), 0 Lux with IR

PAL: 1/12.5 s to 1/50,000 s

Shutter Time

NTSC: 1/15 s to 1/50,000 s

Lens

2.7 mm ~ 13.5 mm motorized varifocal lens with 108.1° to 45.6° horizontal field of view

Lens Mount

φ14

Day & Night

IR cut filter

Angle Adjustment

Pan: 0° ~ 360°; Tilt: 0° ~ 75°; Rotate: 0° ~ 360°

Synchronization

Internal Synchronization

Digital Wide Dynamic

105 dB

Range (DWDR)

AGC

Yes

D/N Mode

Auto / Color/ BW (Black and White)

White Balance

Auto / Manual

BLC

Yes

DWDR

Yes

Functions

Brightness, Sharpness, Digital noise reduction, Mirror, Smart IR, HLC

Interface

Video Output

1 HD analog output (75Ω / BNC)

Switch button

TVI / AHD / CVI / CVBS

General

-40°F ~ 140°F (-40°C ~ 60°C), Humidity 90% or less (non-condensing)

Operating Conditions

Power Supply

9 Vdc to 15 Vdc

Power Consumption

Max. 8.6 W

Protection Level

IP67

Material

Metal

www.observint.com

IR Range

Up to 200 ft

Communication

Up the coax

Dimensions

5.29" × 4.88" × 4.34" (34.3 mm × 123.9 mm × 110.24 mm)

Weight

1.28 lb (580 g) approx.

Cleaning

Clean the camera with an approved glass cleaning solution and a lint free cloth.

Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub

•

the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a

soft cloth.

Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.

•

These may cause damage to the surface over time.

Do not use benzene, thinner or other chemical products on the camera assembly; these may



dissolve the paint and promote damage of the surfaces. Before using any chemical product,

CAUTION

carefully follow the accompanying instructions.

Troubleshooting

Problem

Possible Cause

Nothing appears on the screen

- Check the power connection.

- Check the video signal cable connection to the monitor.

- Check recorder camera settings to verify the video resolution mode of the

camera and recorder match

The video image is dim or not clear.

- If the camera lens is dirty, clean it with a soft, clean cloth.

- Adjust the monitor controls, if necessary.

- If the camera is facing a very strong light, change the camera position.

- Adjust the lens focus.

The screen is dark.

- Adjust the contrast control of the monitor.

- If you have an intermediate device, set the impedance (75 Ω /Hi-Z)

properly, and check the cable connections.

The camera is not working properly and

- Verify that the camera is correctly connected to an appropriate regulated

the surface of the camera is hot.

power source.

The image on the monitor flickers

- Make sure that the camera isn't facing direct sunlight or fluorescent light.

If necessary,change the camera position.