Gardeline EM 700 ELECTRIC Manuel d'alimentation - Page 10

Parcourez en ligne ou téléchargez le pdf Manuel d'alimentation pour {nom_de_la_catégorie} Gardeline EM 700 ELECTRIC. Gardeline EM 700 ELECTRIC 12 pages. Cultivator

Imprimer la page

15. Troubleshooting

Fault
The motor cannot be
The motor cannot be
The motor cannot be
started.
started.
started.
Unusual sounds
Unusual sounds
Unusual sounds
Unusually strong
Unusually strong
Unusually strong
vibration
vibration
vibration
Bad tilling result
Bad tilling result
Bad tilling result
Helpline No. UK / N.IREL AND 0845 603 9277 Rep. Ireland 1890 8823 74
Web Support www.gardenhomepower.com
Model Number: EM 700 Electric Cultivator
Possible cause
No power
No power
No power
Cable damaged
Cable damaged
Cable damaged
Safety switch/plug combination
Safety switch/plug combination
damaged
damaged
Overheating protection is activated
Overheating protection is activated
Overheating protection is activated
Tines are blocked
Tines are blocked
Tines are blocked
Lubricating agent is leaking
Lubricating agent is leaking
Screws, nuts or other fastening
Screws, nuts or other fastening
Screws, nuts or other fastening
elements are loose
elements are loose
elements are loose
Tines are damaged or worn out
Tines are damaged or worn out
Tines are damaged or worn out
Working depth too deep.
Working depth too deep.
Working depth too deep.
Working depth too low.
Working depth too low.
Working depth too low.
Worn-out/blunt tines.
Worn-out/blunt tines.
Worn-out/blunt tines.
Rectifi cation
Check mains supply.
Check mains supply.
Check mains supply.
Check cable, pull the plug and insert again,
Check cable, pull the plug and insert again,
Check cable, pull the plug and insert again,
if required, replace the cable or have it
if required, replace the cable or have it
if required, replace the cable or have it
repaired by a qualifi ed electrician
repaired by a qualifi ed electrician
repaired by a qualifi ed electrician
Have the tool repaired by a specialist
workshop.
1. Working depth too deep, continue work with
1. Working depth too deep, continue work with
1. Working depth too deep, continue work with
less working depth
2. Tines are blocked, remove blocking.
2. Tines are blocked, remove blocking.
2. Tines are blocked, remove blocking.
3. Soil is too hard, adapt working depth accordingly
3. Soil is too hard, adapt working depth accordingly
3. Soil is too hard, adapt working depth accordingly
and work soil by repeatedly moving forward
and work soil by repeatedly moving forward
and work soil by repeatedly moving forward
and backward over the same place.
and backward over the same place.
and backward over the same place.
Let the motor cool down for about 15 minutes
Let the motor cool down for about 15 minutes
Let the motor cool down for about 15 minutes
before you resume your work.
before you resume your work.
before you resume your work.
Switch the tool off, wait until the motor fully stops.
Switch the tool off, wait until the motor fully stops.
Switch the tool off, wait until the motor fully stops.
Have the tool repaired by a specialist
workshop.
workshop.
workshop.
Fasten all elements; if the sounds remain
Fasten all elements; if the sounds remain
Fasten all elements; if the sounds remain
contact a specialist workshop.
contact a specialist workshop.
contact a specialist workshop.
Replace the tines or have them checked by a
Replace the tines or have them checked by a
Replace the tines or have them checked by a
specialist workshop.
specialist workshop.
specialist workshop.
Adjust working depth to a suitable depth.
Adjust working depth to a suitable depth.
Adjust working depth to a suitable depth.
Adjust working depth to a suitable depth.
Adjust working depth to a suitable depth.
Adjust working depth to a suitable depth.
Replace the tines or have them checked by a
Replace the tines or have them checked by a
Replace the tines or have them checked by a
specialist workshop.
specialist workshop.
specialist workshop.
10