KitchenAid KGRT607HWH8 Manuel d'instructions d'installation - Page 9
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} KitchenAid KGRT607HWH8. KitchenAid KGRT607HWH8 12 pages. 30" freestanding sealed burner gas range with self-cleaning thermal/convection oven
Imprimer la page
Check operation
EJeetronie
ignition
system
Cooktop
and oven
burners
use electronic
ignitors
in place
of standing
pilots.
When
a cooktop
control
knob
is turned
to the
"LITE"
position,
the system
creates
a
spark
to light
the burner.This
sparking
continues
until
the control
knob
is turned
to the desired
setting.
When
the oven
control
is turned
to the
desired
setting,
a glow
bar heats
up
bright
orange
and ignites
the gas.
No
sparking
occurs
and the glow
bar
remains
on while
the burners
operate.
Cheek operation
of eooktop
burners
[] Push in and
OFF
turn
each control
knob
"
to the "LITE"
position.
_ t__,_
The flame
should
light
within
4 seconds.The
first
time
a burner
is
lighted
it maytake
_ °*_.
j
longer
than
4seconds
_°
'',*'_o
to light
because
of air
_b
MeO
in gas line.
Lo
[] If burners
do not light
properly,
turn
cooktop
control
knob
to
the "OFF"
position.
Check that the power
supply
cord
is plugged
in and the circuit
breaker
or fuse
has not blown.
Check that
the gas shutoff
valves
are set to the
"open"
position,
Repeat
Step
21. ff a
burner
does
not light
at this
point,
contact
your
KitchenAid
dealer
or
authorized
service
company
for
assistance.
[] Adjust
the height
of top burner
flames
(some
models}.
Push in and turn
each cooktop
control
knob
from
"LJTE"
to "LO"
setting
quickly.
The cooktop
"LO"
burner
flame
should
be a steady
blue
flame
approximately
1/4"
(0.64 cm} high.
It can
be
adjusted
using
the
adjustment
screw
in the
center
of the valve
stem.The
valve
stern
is located
directly
underneath
the control
knob.
if the "LO"
flame
needs
to be adjusted:
a. Remove
the control
knob.
__J
adiustment screw
_
,__//
b. Hold
the knob
stem
with
a pair of
pliers.
Use a small
flat-blade
screwdriver
to turn
the screw
located
in the center
of the control
knob
stem
until
the flame
is the
proper
size.
c. Replace
the control
knob.
d.Test
the flame
by turning
the
control
from
"LO"
to "Hi '/checking
the flame
at each setting.
low flame
high flame
Top burner
flame
appearance
Cheek operation
of oven
burner
Open
oven
door.
Remove
the oven
rack
Remove
the oven
bottom
and place
it on a protected
surface.
[] Push the "BAKE"
pad and
"350°F '' will
appear
in the temperature
displa%
Press the "START"
pad.
"LO"
will
appear
in the display;
then
"170°E"
The
oven
burner
should
light
in 50 to 60
seconds.This
delay
is normaLThe
oven
safety
valve
requires
a certain
time
before
it will
open
and allow
gas to flow.
Electric
ignitors
are used to light
the
oven
and broil
burners.
Do not insert
any object
into the opening
of the protective
shield
that surrounds
the igniton
Do not dean
the area_
@
oven rear
oven burner
\ ignitor
Check the oven
burner
for proper
flame.This
flame
should
have
a 1/2"
(1.3 cm) long
inner
cone
of
bluish-green,
with
an outer
mantle
of dark
blue,
and
should
be clean
and soft
in
character,
No yellow
tips,
blowing
or
lifting
of flame
should
occun
[] If the oven
flame
needsto
be
adjusted,
locate
the air shutter
near the
center
rear
of range.
Loosen
the locking
screw
and rotate
the air shutter
until
the
proper
flame
appears.Tighten
locking
screw.
oven burner
air shutter-
air shutter
rotate to
location
adiust for
ser flame
oven burner
locking
"" brass orifice
screw
hood (nut)
Push "CANCEL/OFF"
pad.
Insert
oven
bottom
tabs
into slots
in oven
burner
area.
Check that tabs
are correctly
placed
in slots.
If the oven
bottom
is not
positioned
properly,
poor
baking
performance
could
occur.
Replace
oven
racks.