KitchenAid YMER8850DS1 Manuel d'instructions d'installation - Page 6

Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} KitchenAid YMER8850DS1. KitchenAid YMER8850DS1 16 pages. 30" (76.0 cm) freestanding electric ranges

Imprimer la page

1. Table of Contents

Wall M ounting

Using the Phillips screwdriver, mount anti-tip bracket to the

wall or floor with the two #12 x 1%" screws provided.

6. Move range close enough to opening to allow for final

electrical connections.

Remove shipping base, cardboard or

hardboard from under range.

7. Move range into its final location, making sure rear leveling leg

slides into anti-tip bracket.

8. Move range forward onto shipping base, cardboard or

hardboard to continue installing the range using the following

installation instructions.

y, Ao' °T

........

On Ranges Equipped with a Storage Drawer:

1. Remove the storage drawer. See "Storage Drawer" section.

2. Use a flashlight to look underneath the bottom of the range.

3. Visually check that the rear range foot is inserted into the slot

of the anti-tip bracket.

On Ranges Equipped

with a Warming Drawer or Premium

Storage Drawer:

1. Place the outside of your foot against the bottom front of the

warming drawer or premium storage drawer, and grasp the

lower right or left side of the control panel as shown.

NOTE: If your countertop is mounted with a backsplash, it

may be necessary to grasp the range higher than is shown in

the illustration.

2. Slowly attempt to tilt the range forward.

If you encounter immediate resistance, the range foot is

engaged in the anti-tip bracket.

3. If the rear of the range lifts more than 1/2"(1.3 cm) off the floor

without resistance, stop tilting the range and lower it gently back

to the floor. The range foot is not engaged in the anti-tip bracket.

IMPORTANT: If there is a snapping or popping sound when lifting

the range, the range may not be fully engaged in the bracket. Check

to see if there are obstructions keeping the range from sliding to the

wall or keeping the range foot from sliding into the bracket. Verify

that the bracket is held securely in place by the mounting screws.

4. Slide the range forward, and verify that the anti-tip bracket is

securely attached to the floor or wall.

5. Slide range back so the rear range foot is inserted into the slot

of the anti-tip bracket.

IMPORTANT: If the back of the range is more than 2" (5.1 cm)

from the mounting wall, the rear range foot may not engage the

bracket. Slide the range forward and determine if there is an

obstruction

between the range and the mounting wall. If you need

assistance or service, refer to the "Assistance or Service" section

of the Use and Care Guide, or the cover or "Warranty" section of

the User Instructions, for contact information.

6. Repeat steps 1 and 2 to ensure that the range foot is engaged

in the anti-tip bracket.

If the rear of the range lifts more than 1/2"(1.3 cm) off the floor

without resistance, the anti-tip bracket may not be installed

correctly. Do not operate the range without anti-tip bracket

installed and engaged. Please reference the "Assistance

Service" section of the Use and Care Guide, or the cover or

"Warranty" section of the User Instructions, to contact service.

Determine if you have AquaLift ®Technology or Steam Clean by

referring to the "Range Care" section of the User Instructions.

For Ranges with AquaLift ®Technology

or Steam Clean:

1. Place level on the oven bottom as indicated in one of the two

figures below depending on the size of the level. Check with

the level: side to side and front to back.

2. If range is not level, pull range forward until rear leveling leg is

removed from the anti-tip bracket.

3. Follow the directions in Style 1 or Style 2, depending on the

style of drawer supplied with the range.

For Ranges without AquaLift ®Technology or Steam Clean:

1. Place a standard flat rack in oven.

2. Place level on the rack and check levelness of the range, first

side to side; then front to back.

3. If range is not level, pull range forward until rear leveling leg is

removed from the anti-tip bracket.

4. Follow the directions in Style 1 or Style 2, depending on the

style of drawer supplied with the range.

Style 1: Ranges Equipped with a Storage Drawer:

Use a 1_,,drive ratchet, wrench or pliers to adjust leveling legs

up or down until the range is level. Push range back into

position. Check that rear leveling leg is engaged in the anti-tip

bracket.