KitchenAid KEMC378KSS - ARCHITECT Series 27'' Microwave Combination Double Wall Oven Instructions d'installation - Page 3
Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} KitchenAid KEMC378KSS - ARCHITECT Series 27'' Microwave Combination Double Wall Oven. KitchenAid KEMC378KSS - ARCHITECT Series 27'' Microwave Combination Double Wall Oven 5 pages. 27" and 30" electric built-in microwave/ oven combination
Également pour KitchenAid KEMC378KSS - ARCHITECT Series 27'' Microwave Combination Double Wall Oven : Liste des pièces (12 pages)
Imprimer la page
Electrical requirements
If codes permit and a separate grounding wire is
used, it is recommended that a qualified electrician
determine that the grounding path and wire gauge
are in accordance with local codes.
Do Not ground to a gas pipe.
Check with a qualified electrician if you are not
sure oven is properly grounded.
Do Not have a fuse in the neutral or grounding
circuit.
This oven must be connected to a grounding metal,
permanent wiring system.
Oven must be connected to the proper electrical
voltage and frequency as specified on the
model/serial rating plate. (The model/serial rating
plate is located on the oven door or on the oven
frame.)
Models rated from 7.3 to 9.6 kW at 240 volts
(5.5 to 7.2 kW at 208 volts) require a separate
40-ampere circuit. Models rated at 7.2 kW and
Installation Steps
Preparation
A
WARNING
Excessive Weight Hazard
Use two or more people to move and
install oven.
Failure to follow this instruction can
result in back or other injury.
Important: Use both hands to remove oven
doors.
Do Not use handle or any portion of the front
frame or trim for lifting.
Before moving oven across floor, check that oven
is on shipping base or slide oven onto cardboard
or hardboard.
Do Not remove shipping feet at the front lower
corners of oven.
Do Not
remove
shipping feet.
1.
Turn power supply off. Move oven
close to final position.
• Remove and discard shipping materials,
tape and protective film from the oven. Do
Not remove shipping base or shipping feet
at the front lower corners of oven. The
shipping feet will protect the lower oven
trim until oven is inserted into cabinet.
• Remove and set aside racks and other parts
from inside oven.
Page 2
below at 240 volts (5.4 kW and below at 208
volts) require a separate 30-ampere circuit.
A time-delay fuse or circuit breaker is
recommended.
Connect directly to the fused disconnect (or
circuit breaker box) through flexible, armored
or non-metallic sheathed, copper cable (with
grounding wire).
Flexible armored cable from appliance should
be connected directly to junction box.
Fuse both sides of the line.
A U.L.-listed conduit connector must be
provided at the junction box.
Do Not cut the conduit.
Wire sizes and connections must conform with the
rating of the appliance and to the requirements of
the National Electrical Code, ANSI/NFPA 70 — latest
edition (*, See Page 1) and all local codes and
ordinances.
Remove
A
side trim
pieces.
power
B
supply cable
shipping
A
foot
latch on the hinge
in locked position –
door free to open
and close
2.
Completely open oven door. In both back
corners of the door you will see door latches in the
locked position. Rotate both latches forward to the
unlocked position.
Grasp outside edges of door with both hands.
• Begin closing door, at the moment the door
stops closing, lift and pull door toward you.
• Set door aside on a protective surface.
If the house has aluminum wiring, follow the
procedure below.
a.) Connect the aluminum wiring to the copper
wire using special connectors designed and
Underwriters Laboratories-listed for joining
copper to aluminum. Follow the electrical
connector manufacturer's recommended
procedure.
b.) Aluminum/copper connection must conform
with local codes and industry-accepted wiring
practice.
Grasp oven frame
C
to lift oven.
Remove
A
oven racks.
Replace
C
oven door.
latch on the hinge
in unlocked
position – door
ready for removal
3.
Remove trim screws attaching right and
left side trim to oven. Grasp the bottom end of
trim and pull away from oven. Slide top end of
trim downward to remove trim from oven. Take
care not to scratch other surfaces with ends of
trim. Set trim and screws aside on protected
surface.
Check oven and
D
microwave oven operation.
Use screws to attach
C
oven to cabinet.
Reattach side
C
trim pieces.
Remove
A
trim screws.
Remove
A
oven door.
Remove trim screw.
Pull trim out.
Pull top of trim
down.