KitchenAid KFID500ESS Manuel d'instructions d'installation - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} KitchenAid KFID500ESS. KitchenAid KFID500ESS 16 pages. Freestanding induction range with double ovens

Imprimer la page

Anti-Tip

Bracket

Range Foot

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

■

Tape measure

■

Level

■

Phillips screwdriver

■

Flat-blade screwdriver

Parts Supplied

Check that all parts are included.

■

3 - 10-32 hex nuts (attached to terminal block)

■

3 - terminal lugs

■

Oven racks

■

2 - #12 x 1⁵⁄₈" screws (for mounting anti-tip bracket)

■

Anti-tip bracket (taped inside upper oven with package

containing literature)

Anti-tip bracket must be securely mounted to back wall or

floor. Thickness of floor may require longer screws to anchor

bracket to subfloor. Longer screws are available from your

local hardware store.

Parts Needed

If using a power supply cord:

■

A UL listed power supply cord kit marked for use with ranges.

The cord should be rated at 250 volts minimum, 40 amps or

50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm)

diameter connection opening and must end in ring terminals

or open-end spade terminals with upturned ends.

■

A UL listed strain relief.

Check local codes. Check existing electrical supply. See

"Electrical Requirements" section.

It is recommended that all electrical connections be made by a

licensed, qualified electrical installer.

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

To verify the anti-tip bracket is installed and engaged:

• Slide range forward.

• Look for the anti-tip bracket securely attached to floor or wall.

• Slide range back so rear range foot is under anti-tip bracket.

• See installation instructions for details.

INSTALLATION REQUIREMENTS

■

Wrench or pliers

³⁄₈" nut driver

■

Hand or electric drill

¹⁄₈" (3.2 mm) drill bit

■

WARNING

Tip Over Hazard

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■

It is the installer's responsibility to comply with installation

clearances specified on the model/serial/rating plate. The

model/serial/rating plate is located behind the control panel.

■

To eliminate the risk of burns or fire by reaching over the

heated surface units, cabinet storage space located above

the surface units should be avoided. If cabinet storage is to

be provided, the risk can be reduced by installing a range

hood that projects horizontally a minimum of 5" (12.7 cm)

beyond the bottom of the cabinets.

■

Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

■

The floor anti-tip bracket must be installed. To install the anti-

tip bracket shipped with the range, see "Install Anti-Tip

Bracket" section.

■

Grounded electrical supply is required. See "Electrical

Requirements" section.

IMPORTANT: To avoid damage to your cabinets, check with your

builder or cabinet supplier to make sure that the materials used

will not discolor, delaminate or sustain other damage. This range

has been designed in accordance with the requirements of UL

and CSA International and complies with the maximum allowable

wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280). When such standard is not

applicable, the Standard for Manufactured Home Installations,

ANSI A225.1/NFPA 501A or with local codes.

Mobile home installations require:

■

When this range is installed in a mobile home, it must be

secured to the floor during transit. Any method of securing

the range is adequate as long as it conforms to the standards

listed above.

■

Four-wire power supply cord or cable must be used in a

mobile home installation. The appliance wiring will need to be

revised. See "Electrical Connection" section.