Gardena 19080 Manuel de l'opérateur - Page 6
Parcourez en ligne ou téléchargez le pdf Manuel de l'opérateur pour {nom_de_la_catégorie} Gardena 19080. Gardena 19080 9 pages. Smart automatic home & garden pump
Également pour Gardena 19080 : Manuel d'utilisation (18 pages)
Imprimer la page
4. If the error is not fixed, go back to step 1 and call up the next
possible error.
5. When the error is fixed, the error display is cleared.
The pump is ready for operation again.
Problem
Possible Cause
Error-LED flashes 1 time
The pump does not pump water for 30 seconds during the
(with a 2 second break)
initial operation.
Pump does not suck water
Pump was not sufficiently
filled with liquid to be pumped.
Air cannot escape on the pres
sure side, because the pressure
side outlets are closed.
Pump does not start
The pump housing has heated
up and the thermal circuit brea
ker has been activated.
The impeller is blocked.
The flow sensor is dirty.
Error-LED flashes
The pump does not pump water for 6 minutes during the
initial operation.
2 times (with
a 2 second break)
Pump does not suck water
Problem on the suction side.
Suction hose deformed
or bent.
Pump does not start
The thermal circuit breaker
has been activated
(motor overheated).
Error-LED flashes
The pump does not pump water for 30 seconds during the
3 times (with
current operation.
a 2 second break)
Water supply disrupted
Problem on the suction side.
on the suction side
Suction hose deformed or bent. v Use a new suction hose.
Pump does not start
The thermal circuit breaker
has been activated
(motor overheated).
The flow sensor is dirty.
Error-LED flashes
The pump switches off during on-going operation after
4 times (with
60 minutes or 2 minutes.
a 2 second break)
Leakage warning is
Leak on pressure side
activated
(e. g. dripping tap).
Problem
Leakage warning is
activated
Remedy
v Fill the pump and make sure
Pump does not start
that water does not drain out
or stops suddenly during
on the pressure side during
operation
the suctioning process
(see 3. OPERATION).
v Open the pressure side
outlets (see 3. OPERATION).
1. Open possible shutoff device
in the pressure line (release
pressure).
To loosen the impeller [ Fig. T1 ]:
2. Ensure sufficient ventilation
If the impeller is stuck due to dirt, the Error LED flashes 1 time
and let the pump cool down
for 20 min.
(with a 2 second break).
1. Turn the motor shaft
1. Loosen the impeller (see
"To loosen the impeller").
2. Let the pump cool down for
2. Start the pump (see 3. OPERATION).
20 min.
v Clean the flow sensor (see
To clean the flow sensor [ Fig. T2 ]:
"To clean the flow sensor").
If the flow sensor is stuck due to dirt, the Error LED flashes
(with a 2 second break).
1. Loosen both screws
2. Remove the cover
v Immerse the suction hose
3. Loosen the screw
end under water.
4. Loosen the cap
v Eliminate any leak on the
5. Remove and clean the impeller
suction side.
v Clean the check valve on
6. Clean the housing of the flow sensor.
the suction line and check
7. Assemble the impeller
the installation direction.
8. First insert the cover
v Clean the suction filter on the
suction hose end.
v Clean the filter lid seal and
9. Start the pump (see 3. OPERATION).
turn the lid until the stopper
(see 4. MAINTENANCE),
v Clean the filter in the pump.
v Use a new suction hose.
v Let the pump cool down
7. TECHNICAL DATA
for 20 min.
smart Automatic Home &
Garden Pump
Mains voltage
Mains frequency
v Immerse the suction hose
Rated Power /
end under water.
Standby consumption
v Eliminate any leak on the
suction side.
Connection cable
v Clean the check valve on
Max. delivery capacity
the suction line and check
the installation direction.
Max. pressure
v Clean the suction filter on the
Max. delivery head
suction hose end.
v Clean the filter lid seal and
Max. suction height
turn the lid until the stopper
(see 4. MAINTENANCE),
Cut-in pressure
v Clean the filter in the pump.
Permitted internal pressure
(delivery side)
SRD:
v Let the pump cool down for
20 min.
v Clean the flow sensor (see
"To clean the flow sensor").
Weight
Sound power level L
measured/guaranteed
Uncertainty k
v Eliminate any leak on the
pressure side.
Measuring process complying with:
Possible Cause
The maximum duration of
the set leakage warning
(low quantity program 60 min.
or 2 min.) has been exceeded
The check valve is blocked.
The flow sensor is dirty.
Mains plug is disconnected.
Power failure.
RCD has triggered
(residual current).
Electrical interruption.
(16)
with a screw driver.
This will loosen the blocked impeller.
(17)
.
(18)
.
(19)
and remove the clip
(21)
counterclockwise (e. g. with a screwdriver).
(22)
again in reverse order.
(18)
at the top and then tighten both screws
at the bottom.
NOTE: For any other malfunctions please contact the GARDENA service
department. Repairs must only be done by GARDENA service departments
or specialist dealers approved by GARDENA.
Unit
V (AC)
Hz
W
m
l/h
bar
m
m
bar
bar
Frequency range
MHz
Maximum power
mW
Free field radio range
m
(approx.)
kg
:
1)
WA
dB (A)
1)
WA
RL 2000/14/EC
1)
Remedy
v Increase the duration
of the leakage warning.
v Increase the water
consumption
v Clean the check valve (see
"To clean the check valve").
v Clean the flow sensor (see
"To clean the flow sensor").
v Connect the mains plug.
v Check the fuse and the
cables.
v Disconnect the pump and con
tact the GARDENA Service.
v Disconnect the pump and con
tact the GARDENA Service.
(20)
.
(22)
.
Value (Art. 19080)
230
50
1300 / 1,5
1.5 (H07RNF)
5000
5.0
50
8
2.0 – 2.8 ± 0.2
6
863 – 870
25
100
13.4
77 / 79
2.19
(17)
7