KitchenAid GZ7930XHS1 Manuel d'utilisation et d'entretien - Page 7

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation et d'entretien pour {nom_de_la_catégorie} KitchenAid GZ7930XHS1. KitchenAid GZ7930XHS1 16 pages. 30"/36" retractable downdraft vent systems

Imprimer la page
6" (15.2 cm) round
vent system
90 ° elbows
,_--6 ft. (1.8 m) -:_-I
I
Maximum
length
= 35 ft. (8.9 m)
1 - wall cap
=Oft.
(Ore)
8ft. (2.4 m) straight
=8ft.
(2.4 m)
2-90 ° elbows
=lOft.
(3m)
Transition
=4.5 ft.
(1.4 m)
Length of 6"
(15.2 cm) system
= 22.5 ft. (6.8 m)
Recommended
standard
fittings
13-1/4" x 10"
(8.3 cm x 25.4 cm)
to 6" (15.2 cm)
= 4.5 ft. (1.4 m)
3-1/4" x 10"
(8.3 cm x 25.4 cm
to 6" (15.2 cm)
90 ° elbow =
5 ft. (1.5 m)
6" (15.2 crn) to
3-1/4" x 10"
(8.3 cmx
25.4 cm)
= 1 ft. (0.3 m)
6" (15.2 cm) to
3-1/4" x 10"
(8.3 cm x 25.4 cm)
90 ° elbow =
5 ft. (1.5 m)
90 ° elbow = 45 ° elbow =
6" wall cap =
5ft.(1.Sm)
2.3 ft. (0.8m)
0ft.(0m)
Excessive Weight Hazard
Use two or mere people to move
and install downdraft vent.
Failure to de so can result in back
or other injury.
= Put on gloves and safety
glasses. Place cardboard
or
another form of protection
on top
of a flat surface where you can
easily assemble
the downdraft
vent system. Remove parts
packages, downdraft
vent and
blower
box from carton and set
on protective
surface. Remove all
shipping
materials,
tape and
protective
film from downdraft
vent and blower box.
over counter
support
arm
[] Attach the left side and right
side overcounter
support
brackets
to the downdraft.
Use 1 screw
with each bracket.
end cap
[] Attach the left side and right
side end caps to the downdraft.
Use 1 screw with each end cap.
_--,,L../
bupport
leg
_ Attach support
legs to side
of downdraft
vent with 2 screws
in each leg. Do not tighten
screws.
_ Carefully
insert downdraft
vent into countertop
cutout.Two
people are recommended
to
support the weight
of the
downdraft
vent during
lifting.
Check that downdraft
vent is
parallel to side of cutout and that
mounting
brackets overlap
countertop.
level
mark
l;
6_
Move support
legs down
against
cabinet
floor. Place a level
against
front of downdraft
vent
base and adjust
until downdraft
vent is level vertically.
Use a
pencil to mark the top of each leg
on downdraft
vent.Then
mark
location of support
leg mounting
holes on cabinet floor. Remove
downdraft
vent from cutout. Drill
starter holes at each mounting
screw location on cabinet floor.
Align top of legs with pencil
marks on the face of the
downdraft
vent.Tighten
screws in
legs.
_ Determine
which direction
(down, rear, left, or right) vent
will need to run from blower
vent
when installed
in cabinet.
Down venting:
Downdraft
vent is shipped with
blower
in down venting
position
so no modification
is required.
Go to Step 8.
Left or right venting:
a. Remove 4 hex nuts that attach
blower
box to downdraft
vent
base. Remove blower
box.
b. Rotate blower
box 90 ° to left or
right so that vent blower
is
repositioned
in the direction
needed.
c. Reattach
blower
box to
downdraft
vent
base with
4 hex
nuts.
Rear venting:
a. Remove 4 hex nuts that attach
blower
box to downdraft
vent
base. Remove blower
box.
b. Note how wiring
cable is
installed under plastic clips
inside vent base.Then
carefully
remove wiring
cable from
plastic clips.
Disconnect
blower wiring
cable.
c. Remove 6 Phillips-head
screws
attaching
blower to blower
box.
Remove blower.