Avaya 3616 Series Manuel d'installation - Page 7

Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} Avaya 3616 Series. Avaya 3616 Series 19 pages. Wireless telephones
Également pour Avaya 3616 Series : Manuel de référence rapide (1 pages), Manuel de référence rapide (2 pages), Manuel de référence rapide (2 pages)

Imprimer la page

Installation Guide

delay to the overall network, which are generally not tolerable for real-time voice connections. Avaya

does not support a configuration that includes wireless bridges and does not recommend using

wireless bridges with any wireless network supporting voice.

Power

2.3.2 Transmission Power

The transmission power of APs can be increased or decreased, to provide more or less AP radio

coverage. For Avaya handsets, the transmission power setting must be the same for all APs in a

facility. This will minimize the opportunity for higher-power devices to interfere with nearby lower-

power devices, while providing consistent coverage.

Avaya wireless telephones support statically configured transmission power settings in the range from

5mW to 100mW. Lower power settings on the APs and handsets can be used to provide added overall

capacity by increasing the density of access points in the network. In such deployments, special

attention must be given to AP placement, to ensure there are no frequency reuse issues. Regardless

of the selected power level settings, all APs and handsets must be configured with the same settings

to avoid channel conflicts and unwanted cross-channel interference. For access points that support

automatic transmission power adjustments, Avaya recommends using only static power settings to

ensure optimal performance of the Avaya wireless telephones.

The AP transmit (TX) power should be set so that the handsets receive the required minimum signal

strength, as defined in Section 2.1.2 of this document. For deployments with higher AP density, lower

TX power settings are typically required to prevent channel interference. Maximum AP power settings

vary by band and by channel, and can vary between countries. Local regulations should always be

checked for regulatory compliance considerations. In addition, maximum power output levels may

vary by AP manufacturer.

In mixed 802.11b/g environments, Avaya recommends configuring the TX power of the 802.11b and

802.11g radios to the same setting, if they are separately configurable. For example, set both radio to

30mW to ensure identical coverage on both radios. For mixed 802.11a/b/g environments, where the

AP utilizes all three radios types, AP placement should first be determined by modeling for the

characteristics of 802.11a, since this environment will typically have the shortest range. Then, the TX

power of the 802.11b and 802.11g radios should be adjusted to provide the required coverage levels

for those networks, within the already established AP locations.

Where possible, all APs should be set to the same TX power level within a given radio type. For

example, set all 802.11a radios to 50 mW and set all 802.11b and 802.11g radios to 30 mW. It crucial

to then set the TX power of the handset to match the TX power of the APs. This will ensure a

symmetrical communication link. Mismatched TX power outputs will result in reduced range, poor

handoff, one-way audio and other quality of service issues.

2.3.3 Interference

Interference on a wireless network may originate from many sources. Microwave ovens, Bluetooth

devices, cordless phones and rogue APs are among the many potential sources. In general, devices

that employ or emit radio frequency signals within a given radio coverage area will have the potential

to cause unwanted interference.

Radio frequency spectrum analyzers can be used to help identify the sources of such interference.

Once identified, interference is best mitigated by removing the interfering device(s) from the network

area. Otherwise, it may be possible to change the channel setting of the interfering device to avoid

conflict with the surrounding APs. If this is also not possible, then the channel of the surrounding APs

may be able to be changed to avoid as much frequency overlap with the interfering device.

Octiober 2008