Gardena 874-21 Mode d'emploi - Page 3

Parcourez en ligne ou téléchargez le pdf Mode d'emploi pour {nom_de_la_catégorie} Gardena 874-21. Gardena 874-21 5 pages.

Imprimer la page
Attaching the spray hose
1. Push the short union nut
to the container cap :
2. Push on the spray hose
beginning of the thread
7 8
9
3. Screw the short union nut
and tighten by hand (do not use pliers).
5
1. Remove the spray tube holder
Attaching the shoulder strap :
the arrow).
A
0
2. Guide the shoulder strap
of the spray tube holder
of the container.
B
3. Press the spray tube holder back on until you hear it click
into place.
4. Attach the shoulder strap on the other side of the holder
B
4. Operation
Filling the container :
1. Mix the fluid well.
2. Press the pump handle
remove the pump
3. Pour the fluid into the container up to the maximum mark
C
(5 litres).
D
Please observe the safety and proportioning instructions provid-
E
ed by the manufacturer of the product you are going to spray.
4. Tighten the pump again with the pump handle
(do not use pliers).
Risk of injury !
A
V Never connect your Pressure Sprayer to an air
5. Unlock the pump handle
pump the pump repeatedly (approx. 30 – 40 times) until the
operating pressure is reached.
Any excess pressure escapes through the safety valve
10
7
5
over the spray hose
.
5
so that it covers at least the
8
.
7
onto the container cap
0
from above (direction of
A
through the elongated hole
0
and attach it into the holder
C
down slightly, turn to the left and
D
.
C
by hand
compressor.
C
by turning slightly to the left and
Spraying :
H
9
Adjusting the spray tube :
3
1
B
Setting the spray jet :
I
B
.
5. Cleaning
Cleaning the Pressure
Sprayer :
6. Trouble-Shooting
Cleaning the filter :
3
E
.
J
Problem
Pump does not build up
pressure.
G
1. Press the operating switch
The Pressure Sprayer begins spraying.
G
2. Release the operating switch
The Pressure Sprayer stops spraying.
Setting the permanent lock:
H
v Press the permanent lock
.
G
The operating switch
is pressed down and stays down.
The spray tube can be swivelled 360° in the hand valve.
1
2
1. Unscrew the union nut
on the hand valve
3
2. Turn the spray tube
to the correct position.
1
3. Tighten the union nut
on the hand valve
(do not use pliers).
You can adjust the spray jet from full jet (nozzle closed) to a fine
mist spray (nozzle open).
v Open or close the spray nozzle
you require.
Always clean your Pressure Sprayer after spraying.
v Fill the Pressure Sprayer with clean water (the water may
contain some washing-up liquid if necessary) and empty out
the water by spraying it through the spray tube in the same
way as when spraying a product.
This cleans the valves, the spray tube and the nozzles.
We recommend that you have your Pressure Sprayer thoroughly
inspected (preferably at a GARDENA Service Centre) after
using it for 5 years.
If the spray jet from the Pressure Sprayer is very weak you
should clean the filter in the container.
J
v Remove the sieve
from the spray tube
Possible Cause
Safety valve is loose.
Hose connection at the container v Tighten the hose connec-
and hand valve is not tight.
on the handle.
G
on the handle.
2
.
2
by hand
I
according to the spray jet
3
and clean it.
Remedy
v Tighten the safety valve.
tions at the container and
hand valve.
11