Garmin GPSMAP 4010 Manuel d'instructions d'installation - Page 16

Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} Garmin GPSMAP 4010. Garmin GPSMAP 4010 25 pages. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Également pour Garmin GPSMAP 4010 : Manuel d'instructions d'installation (25 pages), Manuel de référence rapide (2 pages), Référence technique (42 pages), Informations importantes en matière de sécurité (48 pages), Déclaration de conformité (1 pages), Important Information (2 pages), Manuel complémentaire (24 pages)

Garmin GPSMAP 4010 Manuel d'instructions d'installation

Advanced NMeA 0183 Wiring

The GPSMAP 4000/5000 series chartplotter features four ports to receive NMEA 0183 data (RX ports), and two ports to send NMEA 0183 data
(TX ports). Wire one NMEA 0183 device per RX port to send data to a 4000/5000 series chartplotter, wire up to three NMEA 0183 devices in
parallel to each TX port to receive data from a 4000/5000 series chartplotter.
Each RX and TX port has 2 wires, labeled A (+) and B (-) according to the NMEA 0183 convention. Connect the corresponding A (+) and B (-)
wires of each port to the A (+) and B (-) wires of your NMEA 0183-compliant device. Refer to the table and wiring diagrams when wiring the
4000/5000 chartplotter to NMEA 0183 devices.
Consult the installation instructions of your NMEA 0183-compliant device to identify the transfer (tX) A(+) and B(-) wires and
Receiving (RX) A(+) and B(-) wires. Use 28 AWG, shielded, twisted-pair wiring for extended runs of wire. Solder all connections and seal the
connection with heat-shrink tubing.
Notes:
For two-way communication with a NMEA 0183 device, the ports on the GPSMAP 4000/5000 chartplotters are not linked. For example,
if the RX port of the NMEA-compliant device is wired to TX port 1 on the GPSMAP 4000/5000, you can wire the TX port of your NMEA
0183-compliant device to RX port 1, port 2, port 3, or port 4 on the GPSMAP 4000/5000.
The ground wires on the NMEA 0183 data cable from the GPSMAP 4000/5000 series chartplotter and your NMEA 0183-compliant device
must both be grounded.
Approved NMEA 0183 sentences—GPBWC, GPRMC, GPGGA, GPGSA, GPGSV, GPGLL, GPBOD, GPRMB, GPRTE, GPVTG,
GPWPL, GPXTE, and Garmin proprietary sentences—PGRME, PGRMM, and PGRMZ.
The GPSMAP 4000/5000 series chartplotter also includes support for the WPL sentence, DSC, and sonar NMEA 0183 input with support for
the DPT (depth) or DBT, MTW (water temperature), and VHW (water temperature, speed, and heading) sentences.
Use the Communications section of the Configure menu on the GPSMAP 4000/5000 series chartplotter to set up NMEA 0183
communications. See the owner's manual for details.
Port
receiving
Port 1
receiving
Port 2
receiving
Port 3
receiving
Port 4
Transmitting
Port 1
Transmitting
Port 2
N/A
N/A
N/A
N/A
N/A
N/A
N/A
1
Wire Function
rX / A (+)
rX / B (-)
Orange/White
rX / A (+)
rX / B (-)
Brown/White
rX / A (+)
rX / B (-)
Violet/White
rX / A (+)
Black/White
rX / B (-)
TX / A (+)
TX / B (-)
TX / A (+)
TX / B (-)
GPS 17 IN
Green/White
GPS 17 OUT
SPAre
AlArM
ACCeSSOry ON
GrOUND
SPAre
GPSMAP 4000/5000 Series NMeA 0183 Data Cable
Wire Color
Pin Number
White
Brown
Violet
red/White
Gray
Pink
Blue
Blue/White
Green
yellow
Orange
Black
Connector
1
2
5
6
9
10
PIN 1
PIN 1
11
12
3
PIN 8
PIN 8
4
7
PIN 17
PIN 17
8
NMeA 0183 Cable
NMeA 0183 Cable
13
end View
end View
14
15
16
17
18
19
GPSMAP 4000/5000 Series Installation Instructions
PIN 3
PIN 3