Fujitsu LIFEBOOK LH532 Manuel - Page 2
Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Fujitsu LIFEBOOK LH532. Fujitsu LIFEBOOK LH532 18 pages. Lifebook ah series; lifebook lh series
Imprimer la page
- 1. Fujitsu Lifebook
- 2. AH / LH Series BIOS
- 3. Bios Setup Utility
- 4. Navigating through the Setup Utility
- 5. Info Menu - Displays Basic System Information
- 6. System Menu - Setting Standard System Parameters
- 7. Advanced Menu - Setting Device Feature Controls
- 8. Security Menu - Setting the Security Features
- 9. Item Specific Help
- 10. Hard Disk Security
- 11. Security Chip
- 12. Boot Menu - Selecting the Operating System Source
- 13. Exit Menu - Leaving the Setup Utility
S T Y L I S T I C L H 5 3 2 / A H 5 3 2 B I O S
AH / LH Series BIOS
BIOS SETUP UTILITY
The BIOS Setup Utility is a program that sets up the
operating environment for your notebook. Your BIOS
is set at the factory for normal operating conditions,
therefore there is no need to set or change the BIOS
environment to operate your notebook.
The BIOS Setup Utility configures:
Device control feature parameters, such as
n
changing I/O addresses and boot devices.
System Data Security feature parameters, such
n
as passwords.
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility, do the following:
1. Turn on or restart your notebook.
2. Press [F2] once the Fujitsu logo appears on the
screen. This will open the main menu of the BIOS
Setup Utility with the current settings displayed.
3. Press the [RIGHT ARROW] or [LEFT ARROW] key to
scroll through the other setup menus to review or
alter the current settings.
The Boot Menu can also be invoked by pressing the
[F12] key when the Fujitsu logo appears on the
screen.
Navigating through the Setup Utility
The BIOS setup utility consists of six menus: Info,
System, Advanced, Security, Boot, and Exit. This docu-
ment explains each menu in turn, including all
submenus and setup items.
The following procedures allow you to navigate the
setup utility menus:
1. To select a menu, use the cursor keys:
2. To select a field within a menu or a submenu, use
the cursor keys:
[ ], [ ].
3. To select the different values for each field, press
the [Spacebar] or [+] to change to the next lower
selection and [F5] or [-] to go to the next higher
selection.
4. To activate a submenu press the [Enter] key.
2
5. To return to a menu from a submenu, press the
[Esc] key.
6. To go to the Exit menu from any other menu,
press the [Esc] key.
7. Press the [F9] key to reset all items in the BIOS to
the default values.
8. Press the [F10] key to save the current configura-
tion and exit the BIOS Setup Utility. You will be
asked to verify this selection before it is executed.
9. Press the [F1] key to view a general help screen.
Entering the Setup Utility After a
Configuration Change or System Failure
If there has been a change in the system configuration
that does not agree with the parameter settings stored
in your BIOS memory, or there is a failure in the
system, the system beeps and/or displays an error
message after the Power On Self Test (POST). If the
failure is not too severe, it will give you an opportunity
to modify the setup utility settings, as described in the
following steps:
1. When you turn on or restart the computer there is
a beep and/or the following message appears on
the screen:
Error message - please run SETUP program Press
<F1> key to continue, <F2> to run SETUP
[
], [
].
Selecting a field causes a help message
about that field to be displayed on the
right-hand side of the screen.
Pressing the Enter key with the highlight
on a selection that is not a submenu or
auto selection will cause a list of all
options for that item to be displayed.
Pressing the Enter key again will select
the highlighted choice.