Fujitsu PRIMERGY RX300 S8 Manuel d'instructions - Page 10
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions pour {nom_de_la_catégorie} Fujitsu PRIMERGY RX300 S8. Fujitsu PRIMERGY RX300 S8 31 pages. System configurator and order information guide
Également pour Fujitsu PRIMERGY RX300 S8 : Fiche technique (12 pages)
Imprimer la page
E
III
Section
- There are 12 memory slots per CPU for max.
=> max. 1.536GB for two CPU`s (768GB per CPU), using LRDIMM
- The memory area is divided into 4 channels per CPU with 3 slots per channel
- Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2,
slot 3 belongs to memory bank 3
Registered, LR DIMMs and unbuffered memory modules can be selected
No mix of registered, load reduced and unbuffered modules allowed.
Memory can be operated at 1.5V or 1.35V, even if the modules are of low voltage type.
Memory operating voltage can be set within BIOS (1.5V is default setting for max. speed).
In a single DIMM per channel configuration, following frequencies are supported:
- 1.5V - 1866MHz max (depending on CPU)
- 1.35V - 1600MHz max (depending on CPU, up to two LRDIMM per channel)
- 1.35V - 1333MHz max (up to two UDIMM or RDIMM per channel)
SDDC (Chipkill) is supported for registered / load redueced x4 organized memory modules only
In a 3 DIMMs per channel configuration, memory will operate at 1.35V or 1.5V (no UDIMM allowed).
SSD (Chipkill) is supported for registered / load reduced x4 organized memory modules only.
1.) In the "Independent Channel Mode" is following configuration possible
Channels can be populated in any order in Independent Channel Mode. All four
channels may be populated in any order and have no matching requirements. All
channels must run at the same interface frequency but individual channels may run at
different DIMM timings (RAS latency, CAS latency, and so forth)
No mix of registered, load reduced and unbuffered modules allowed.
2.) "Rank Sparing Mode" configuration
- Within a memory channel, one rank is a spare of the other ranks.
The Spare Rank is held in reserve and is not available as system memory
For the effective memory capacity, please refer to the spreadsheet below.
The BIOS is set to the rank sparing setting.
Minimum configuration is: 2x 1R, 2x 2R or 1x4R DDR3 module per channel
This mode is not supported by unbuffered memory modules
3.) "Performance Mode" configuration
- In this configuration, the memory module population ex factory is spread across all channels.
The BIOS is set to the max. performance for memory.
Minimum configuration is: 4x identical modules
4.) In the "Mirrored Channel Mode" is following configuration possible
- Each memory bank can optionally be equipped with 4x registered or load reduced or unbuffered DDR3 modules
In each memory bank channel A and B / C and D of CPU 1 or channel E and F / G and H of CPU 2 have to be
equipped with identical modules for mirrored channel mode.
In channel B / D is always the mirrored memory of channel A / B of CPU 1
In channel F / H is always the mirrored memory of channel E / G of CPU 2
Minimum configuration is: 4x identical modules
This mode is not supported by unbuffered memory modules
F
Memory
768GB LRDIMM (12x 64GB 8R)
192GB RDIMM (12x 16GB 2R)
64GB UDIMM (8x 8GB) on special Release only
Fujitsu PRIMERGY Server
System configurator and order-information guide
PRIMERGY RX300 S8
Status 2017-02-28
10 of 31