Fujitsu ScanSnap iScanner fi-6010N Manuel de démarrage - Page 11
Parcourez en ligne ou téléchargez le pdf Manuel de démarrage pour {nom_de_la_catégorie} Fujitsu ScanSnap iScanner fi-6010N. Fujitsu ScanSnap iScanner fi-6010N 21 pages. Network adf scanner
Également pour Fujitsu ScanSnap iScanner fi-6010N : Spécifications (2 pages), Brochure & Specs (2 pages), Manuel de démarrage (21 pages), Manuel de démarrage (45 pages), Instructions de nettoyage (2 pages), Instructions de nettoyage (2 pages)
Imprimer la page
4. Enter the following numerical addresses:
• Primary WINS
• Secondary WINS
If a WINS server setting is not required, enter
"0.0.0.0".
A Secondary WINS cannot be set
without a Primary WINS.
ATTENTION
5. Press the [OK] button.
⇒
The information entered is set.
Next, check the network connection.
3.9 Checking the Network
Connection
The network connection may be checked by performing
a ping test.
1. Select the [Network Settings] tab on the top
menu.
2. Press the [
] button on the left side menu.
⇒
Scroll the left side menu down until the [Ping]
tab appears.
3. Select the [Ping] tab on the left side menu.
⇒
The "Ping" screen appears.
4. Enter the IP address, host name, or FQDN for
the server to be used to check the network
connection.
• For an IP address
The following format should be used
xxx.xxx.xxx.xxx (xxx is a value from 0 to 255).
• For a host name or FQDN
Up to 255 characters may be used.
5. Press the [Ping] button.
⇒
A ping test is performed and the results are
displayed. If the result shows "Lost=0 (0%
loss)", the network connection is functioning
normally. For any other result, refer to
"Checking Basic Network Operation with a
Ping Test" (page 23).
After performing all settings, restart the system.
3.10 Restarting the System
1. Press the [Logout] button.
⇒
The restart confirmation screen appears.
2. Press the [Restart] button.
⇒
The scanner restarts, and the "Login" screen
appears.
Next, install the Admin Tool.
11
Installing the Admin Tool
Chapter 4
As well as operating via the touch panel, the administra-
tor can configure scanner settings via the network inter-
face. In order to do this, the Admin Tool, or Central
Admin Console, must first be installed on a personal
computer connected to the network.
The Admin Tool can set one scanner at a time. The Cen-
tral Admin Console can set multiple scanners at a time.
For more details about the Central Admin Console, refer
to the "Operator's Guide".
This chapter provides a description of the Admin Tool.
The information and procedure for installing the Admin
Tool are as follows.
•
Software
Operating system
•
Windows® XP SP2 or later
•
Windows Vista®
•
Windows Server® 2003 SP2 or later
•
Windows Server® 2008
•
.NET Framework 2.0 SP1 or later, or
.NET Framework 3.0 SP1 or later (*1)
•
Microsoft® Internet Explorer 6 SP2 or
later (*2)
•
Hardware
32 MB or more of free memory space
•
64 MB or more of free disk space
•
Any personal computer which runs the
supported software
•
XGA monitor or better
•
LAN cable
•
Pointing device (e.g. mouse)
*1: When installing the Admin Tool, confirm that .NET
Framework is installed. If not already installed, a message
will appear telling you to install .NET Framework from
the Microsoft Web site. When installing .NET Frame-
work, at least 280MB of additional free disk space is
required.
*2: Confirm that the latest security patch has been applied. If
the latest patch has not been applied, downloading opera-
tions (such as manual download) may not be possible. For
Windows® XP, "KB933566" must be applied to
Microsoft® Internet Explorer.
1. Specify the scanner name as a URL in the web
browser's location bar.
According to the settings from "3.6 Setting the
Admin Network" (page 9), the specified URL is
as follows:
• SSL is [Off], no port number change
http://scanner_name or IP_address/
• SSL is [Off], port number change
http://scanner_name or IP_address:port_number/
For port_number, number enter the changed port
number
fi-6010N Network Scanner Getting Started
• SSL is [On], no port number change
https://scanner_name or IP_address/
• SSL is [On], port number change
https://scanner_name or IP_address:port_number/
For port_number, enter the changed port number
For SSL, the "Security Alert" window is dis-
played when connecting. Press the [Yes] button
on the "Security Alert" window.
⇒
The "Login" screen appears.
2. Enter a "User Name" and "Password", and
press the "Login" button.
⇒
The "Download" screen appears.
3. Press the [Next] button for the fi Network Scan-
ner Admin Tool download.
⇒
The fi Network Scanner Admin Tool down-
load screen appears.
4.
Press the [Download] button.
12