Indesit BIAAA series Manuel d'utilisation - Page 5
Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Indesit BIAAA series. Indesit BIAAA series 8 pages. Refrigerator/freezer combination
Également pour Indesit BIAAA series : Manuel d'utilisation (12 pages), Manuel d'utilisation (48 pages)
Imprimer la page
Installation
! Before placing your new appliance into operation please read these
operating instructions carefully. They contain important information for
safe use, for installation and for care of the appliance.
! Please keep these operating instructions for future reference. Pass
them on to possible new owners of the appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and condenser
give off heat and require good ventilation to operate correctly and
save energy.
3. Leave a space of at least 10 cm between the top part of the
appliance and any furniture above it, and at least 5 cm between
the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat (direct
sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the appliance
and the wall behind it, fit the spacers supplied in the installation kit,
following the instructions provided.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator by
tightening or loosening the front feet.
Electrical connections
After the appliance has been transported, carefully place it vertically
and wait at least 3 hours before connecting it to the electricity mains.
Before inserting the plug into the electrical socket ensure the following:
• The appliance is earthed and the plug is compliant with the law.
• The socket can withstand the maximum power of the appliance,
which is indicated on the data plate located on the bottom left side
of the fridge (e.g. 150 W).
• The voltage must be in the range between the values indicated on
the data plate located on the bottom left side (e.g. 220-240V).
• The socket is compatible with the plug of the appliance. If the
socket is incompatible with the plug, ask an authorised technician
to replace it ( see Assistance ). Do not use extension cords or
multiple sockets.
! Once the appliance has been installed, the power supply cable and
the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by authorised
technicians only (see Assistance).
The manufacturer declines any liability should these
The manufacturer declines any liability should these
! The manufacturer declines any liability should these
The manufacturer declines any liability should these
The manufacturer declines any liability should these
safety measures not be observed.
safety measures not be observed.
safety measures not be observed.
safety measures not be observed.
safety measures not be observed.
Your appliance is supplied with a 13amp fused plug that can be
plugged into a 13amp socket for immediate use. Before using the
appliance please read the instructions below.
WARNING:
THIS APPLIANCE MUST BE EARTHED.
Replacing fuse covers:
When replacing a faulty fuse, a 13amp ASTA approved fuse to BS
1362 should always be used and the fuse cover re-fitted.
If the fuse cover is lost, the plug must not be used until a replacement
is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the correct colour as
indicated by the coloured marking or the colour that is embossed in
words on the base of the plug.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR 5 YEAR PARTS GUARANTEE ON 08448 24 24 24
Changing the plug:
Removing the plug
If your appliance has a non-rewireable moulded plug and you should
wish to remove it to add a longer cable or to re-route the mains cable
through partitions, units etc. please ensure that either:
- The plug is replaced by a fused 13amp re-wireable plug bearing
the BSI mark of approval.
or
- The mains cable is wired directly into a 13amp cable outlet,
controlled by a switch (in compliance with BS 5733) which is
accessible without moving the appliance.
Disposing of the plug
Cut off and dispose of the supplied plug if it does not fit your socket. The
cable should be cut as close as possible to the moulded plug.
Remove the fuse.
WARNING:
To avoid a shock hazard do not insert the discarded plug
into a socket anywhere else.
Fitting a new plug
IMPORTANT:
WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE
WITH THE FOLLOWING CODE...
Green and Yellow - Earth
Blue
- Neutral
Brown
- Live
As the colours of the wires in the mains lead may not correspond with
the coloured markings identifying the terminals in your plug, proceed
as follows:
- Connect Green and Yellow wire to terminal marked 'E' or
coloured Green and Yellow.
- Connect Brown wire to terminal marked 'L' or coloured red or
brown.
- Connect Blue wire to terminal marked 'N' or coloured Black or
Blue.
If a 13amp plug (BS 1363) is used it must be fitted with a 13amp fuse.
If you are in any doubt about the electrical supply to your
machine, consult a qualified electrician before use.
CE Marking certifies that this appliance conforms to the
following EEC directives:
Low Voltage Equipment - 73/23/EEC & 93/68 EEC
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/
68/EEC
GB
or
5