Kohler Command PRO CH18 Manuel du propriétaire - Page 14

Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} Kohler Command PRO CH18. Kohler Command PRO CH18 21 pages. Command series
Également pour Kohler Command PRO CH18 : Manuel du propriétaire (21 pages), Manuel du propriétaire (21 pages), Manuel du propriétaire (8 pages), Manuel du propriétaire (21 pages), Manuel du propriétaire (24 pages), Manuel du propriétaire (14 pages)

Kohler Command PRO CH18 Manuel du propriétaire
EFI Engines: A special, high volume, high pressure
filter with greater filtration capabilities and internal
surface area is used. See Figure 15.
Fuel Filter
Fuel Line
Figure 15. EFI Fuel Filter and Line.
Replacement is recommended every 1500 hours, or
more frequently under extremely dusty or dirty
conditions. When replacement is necessary, always
use genuine Kohler parts.
Fuel Line
Carbureted Engines: In compliance with CARB Tier
III Emission Regulations, carbureted engines with a
Family identification number beginning with "6" or
greater (see Figure 16), must use Low Permeation SAE
30 R7 rated fuel line; certified to meet CARB
requirements. Standard fuel line may not be used.
Order replacement hose by part number through a
Kohler Engine Service Dealer.
IMPORTANT ENGINE INFORMATION
THIS ENGINE MEETS U.S. EPA AND CA 2005
AND LATER AND EC STAGE II (SN:4) EMISSION
REGS FOR SI SMALL OFF–ROAD ENGINES
FAMILY
6 KHXS.7252 PH
TYPE APP
DISPL. (CC)
MODEL NO.
SPEC. NO.
SERIAL NO.
BUILD DATE
OEM PROD. NO.
EMISSION COMPLIANCE PERIOD:
EPA:
CARB:
CERTIFIED ON:
REFER TO OWNER'S MANUAL FOR HP RATING,
SAFETY, MAINTENANCE AND ADJUSTMENTS
1-800-544-2444 www.kohlerengines.com
KOHLER CO. KOHLER, WISCONSIN USA
Figure 16. Family Number Location.
EFI Engines: A special fuel line, capable of
withstanding the high pressure of the EFI fuel system,
is used (must meet SAE R9 specifications). See Figure
15. If fuel line must be replaced, see your Kohler
Engine Service Dealer.
14
Carburetor Troubleshooting and
Adjustments
Engines in this series use either a one- or two-barrel
carburetor depending on model, and may also be
equipped with a Governed Idle System. Specific
adjustment procedures are provided based on the
model and carburetor involved. If the engine is
equipped with a Governed Idle System, refer to Models
with Governed Idle System on page 15 when
performing any carburetor adjustment, as an
additional step to the listed adjustment procedure(s) is
required.
NOTE: Carburetor adjustments should be made only
The carburetor is designed to deliver the correct
fuel-to-air mixture to the engine under all operating
conditions. To comply with current emission
regulations, the fuel mixture settings are made at the
factory and cannot be adjusted.
NOTE: To ensure correct engine operation at altitudes
Low Idle
Speed Adj.
N11236
Figure 17. Carburetor (CH18-25,CH730,740).

Troubleshooting

If engine troubles are experienced that appear to be
fuel system related, check the following areas before
adjusting the carburetor.
• Make sure the fuel tank is filled with clean, fresh
• Make sure the fuel tank cap vent is not blocked
after the engine has warmed up.
above 1525 meters (5000 ft.), it may be
necessary to have an authorized Kohler dealer
install a special high-altitude jet kit in the
carburetor. If a high-altitude kit has been
installed, the engine must be reconverted to
the original jet size, before it is operated at
lower altitudes, or overheating and engine
damage can result.
gasoline.
and that it is operating properly.
Low Idle
Fuel Adj.
Needle &
Fixed Main Jet
(under optional