AQUA FORTE MWWZ310M-35L-1400WB Manuel - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} AQUA FORTE MWWZ310M-35L-1400WB. AQUA FORTE MWWZ310M-35L-1400WB 18 pages. 3 in 1 wet, dry & pond cleaning vacuum cleaner

Imprimer la page

Thank you for purchasing this multi-purpose vacuum cleaner, a high-quality product based on the newest state-of-the-art technology. The vacuum

cleaner is suitable for use in garden ponds, but can also be used as a wet and dry vacuum cleaner around the home and garden. It is not suitable for

professional use, or for emptying ponds, pools and other containers. Please read the following instructions carefully and thoroughly. Failure to comply with

these requirements could cause serious injury and may result in product damage or failure.

Important!

1. Safety Warnings

• The power supply must correspond to the product speciﬁcation. If necessary, ask for information from your local electricity supplier regarding

connection regulations. Do not connect the device if these do not meet the mentioned regulations (the voltage speciﬁcation must match the

operating voltage).

• The device must be connected to a 30mA RCD (Residual Current Device) for prevent the possibility of electric shock and to comply with Europe safety

standards. Further information is available from your local electricity specialist.

• The device must be fully assembled before use.

• Packing parts may be dangerous (e.g. plastic bags). Therefore, store away from children, domestic animals and anyone incapable of understanding the

dangers. This device is not a toy.

• When cleaning a pond, the device should be positioned with a clearance of 2 meters from the water's edge.

• Never leave the device unattended.

• Never carry or pull the device by the power cable.

• Do not pull the device behind you by the hose during operation.

• Do not cut oﬀ the plug and do not shorten the cable. Your guarantee becomes invalid if this is not observed.

• When using outdoors, ensure that the plug and socket are completely dry.

• Never touch the plug with wet hands.

• When the device is switched on, do not hold the suction nozzle close to sensitive body parts like eyes, ears or mouth.

• Before emptying the vessel, switch oﬀ the device and remove the plug from the RCD.

• Always switch oﬀ the vacuum cleaner and pull out the plug before cleaning the device. Do not immerse the motor head (1) into water for cleaning

purposes or clean with a water jet.

• This device is suitable for sucking water with a maximum temperature of 35 degrees.

• Replacement of the electric cable is not possible. The device must not be operated in the case of a defective electric cable or housing.

• Do not suck up ﬂammable, explosive, poisonous or health hazardous materials with the device.

• We take no responsibility for any damage to persons and objects, caused by incorrect use of the device or by not observing these operating

instructions.

2. Prior to 1st Time Use

• Please read the operating instruction thoroughly.

• Remove all the accessories and packages from the box and inside the main body collection tank (8).

• Check before and after use that the switch is in OFF (0) position.

• Always use the device with the correct ﬁlter insert suitable for the relevant application, i.e. ﬁlter sponge (13) for wet usage, paper bag (16) for dry usage.

• Attach the 4 wheel holders (14) onto the 4 location points on the base of the main body collection tank (8) by pushing down and ﬁx by 4 screws

supplied. Push the 4 wheels (15) into the location holes on the wheel holders (14). The slots on the wheel holders can be used to hold the tools.

3. Motor switch /operating mode

Switch position 0

Motor oﬀ

Switch position I

Manual operation (ON/OFF) for wet/dry vacuuming operation

Switch position II

Automatic operation for pond and cleaning

a) After switching on, the motor will suck for 30 seconds

b) Motor stops after approximately 30 seconds to drain

c) Auto Start after 30seconds

d) Repetition (a) and (b) to OFF (0)

4. Pond Cleaning

Please proceed as follows when using the device for pond cleaning:

• Position the device at a safety clearance of 2 metres away from the water's edge.

• Screw the discharge hose (3) securely onto the water discharge hole on the base of the collection tank (8). Attach the dirt collecting bag (4) to the end

of the discharge hose and place in such a way that the water can easily ﬂow down a drain or to a suitable location in the garden, as silt is generally

accepted as being an excellent general fertilizer. Coarse dirt will be collected in the dirt collection bag (4). Depending on the degree of dirt, the dirt

collecting bag (4) should be emptied at regular intervals whilst cleaning the pond, and emptied and cleaned at the end of each use.

• Open the two locking clips (6) on the side of the collection tank (8) and remove the motor head (1). Fit the ﬁlter sponge (13) over the motor head (1).

Tighten the cord around the motor head. Place the motor head back onto the collection tank, ensuring the locking clips are relocated back into the

corresponding indents on the collection tank, with the electrical cable positioned on the opposite side to the suction hose plug-in connector hole (7).

5 • 3 IN 1 WET, DRY & POND CLEANING VACUUM CLEANER